background image

3                                                         Operating Instructions: DTP08(-Ex)

 

Proprietor Responsibilities 

 
For the p

urposes of the present operating instructions the “proprietor” is defined as any 

natural or legal person who either uses the unit themselves, or on whose behalf it is used. 
In special cases (e.g. leasing or renting) the proprietor is considered the person who, in 
accordance with existing contractual agreements between the owner and user of the 
unit, is charged with operational duties. The proprietor must ensure that the unit is used 
only for the purpose for which it is intended and that there is no danger to life or limb of 
the user and third parties. Furthermore, accident prevention regulations, safety 
regulations and operating, maintenance and repair guidelines must be followed. The 
proprietor must ensure that all users have read and understood these operating 
instructions. The proprietor must perform an onsite risk assessment before the unit is put in 
to service. 
 

IMPORTANT 

Failure to comply with the operating instructions shall invalidate the warranty. The same 
applies if improper work is carried out on the unit by the proprietor or third parties 
without the permission of the manufacturer. 
 

Adding Attachments and/or Accessories 

 
The mounting or installation of additional equipment which affects or enhances the 
performance of the unit requires written permission of the manufacturer. Local authority 
approval may also need to be obtained. Local authority approval does not however 

constitute the manufacturer’s approval. An onsite risk assessment must then be carried 

out. 
 

WARNING - ANY UNAUTHORISED MODIFICATIONS OR ADDITIONS TO THE UNIT SHALL 

INVALIDATE THE WARRANTY AND STS SHALL NOT BE LIABLE. 

 

Safety Regulations for the Operation of the Unit 

 

Operator authorisation 

The unit may only be used by suitably trained personnel, who have demonstrated to the 
proprietor, or their representative that they can operate the unit safely and in 
accordance with the operating instructions. 
 

Operators rights, obligations and responsibilities 

The operator must be informed of their duties and responsibilities and be instructed in 
the operation of the unit and shall be familiar with the operating instructions. Operators 

must be provided the appropriate PPE as mentioned in the ‘Approved Application 
Conditions’ section of this manual.

 

 

Unauthorised use of unit 

The operator is responsible for the unit during the time it is in use. The operator must 
prevent unauthorised persons from operating the unit.  
 

Damage and faults 

The proprietor must be immediately informed of any damage or faults to the unit or 
attachment. Units which are unsafe for operation must be quarantined until faults have 
been rectified and the unit deemed safe for operation. 
 

 
 
 

Содержание DTP04




















Отзывы:

Похожие инструкции для DTP04