Strong International XENON GLADIATOR II Скачать руководство пользователя

Страница: 11 / 55

OPERATION

INSTALL THE GLASS HEAT FILTER into the bracket mounted on the rear of the fadeout

and douser support housing. NOTE: The

coated side

of the filter, with the XX or other marking,

must be

facing the reflector

. Reach through the side door and nose opening of the lamphouse, slide the filter into the slot

in the top angle bracket, and lower it into the bottom slotted bracket.

REMOVE THE PLASTIC COVER from the xenon bulb. DO NOT ignite the lamp with the

cover on the bulb. Store the cover for future re-use.

CLOSE AND SECURE the lamphouse door using the tamperproof screws and special screw-

driver supplied with the lamphouse. Engage the cam lock and install the security screw. The door must be

completely secured to actuate the interlock switch and permit lamp ignition. Place the MODE switch in the

MAN. (manual) position.

TURN ON THE MAIN LINE SWITCH and/or circuit breaker to energize the xenon power

supply. The lamphouse blowers will start and the blower interlock switches will be actuated to permit lamp

ignition. The blowers will operate continuously until the xenon power supply is de-energized.

PLACE THE

LAMP

SWITCH in the ON position and the lamp will ignite. If ignition does

not occur, or the high voltage pulse is not apparent, press the emergency ignition switch on the top of the

lamphouse under the plug button. Do not hold more than

one second

; release immediately upon lamp ignition.

Use of the emergency ignition switch indicates an abnormal condition; see the TROUBLESHOOTING section

following.

CHECK THE READING on the lamphouse ammeter. Nominal current for the 3000 watt

xenon bulb is 95 amperes. DO NOT, AT ANY TIME, exceed 100 amperes. Output current is adjusted at the

power supply; see power supply manual for instructions. Operation of a new bulb is normally started at the

lower end of its range (85 A.), and current is gradually increased as the bulb ages to maintain light output.

PRESS THE SMALL PUSH BUTTON SWITCH located below the ammeter to read the DC

voltage at the arc. This permits immediate calculation of the power at which the lamp is operating (volts times

amperes = wattage). Holding this switch in during the ignition cycle will also briefly indicate the no load

(open circuit) DC voltage applied to the xenon bulb for ignition.

REMOVE THE REAR COVER PLATE below the instrument panel by withdrawing the two

plastic plungers. This exposes the bulb positioning controls in the lamphouse back casting.

TO FOCUS THE XENON BULB and obtain the best light on the stage, the two methods

outlined below are the most suitable.

MOVE THE SPOT SIZE CONTROL HANDLE (trombone) on the large lens carriage all the

way forward to project the smallest spot possible; place the iris, masking shutters (choppers) and the fadeout

douser blades in their full open positions. Project a spot to a wall or similar flat perpendicular surface opposite

the spotlight position.

XG3/009

Содержание XENON GLADIATOR II
























































Результаты поиска

Содержание XENON GLADIATOR II

Отзывы:

Похожие инструкции для XENON GLADIATOR II

Бренды по названию

Популярные бренды

Strong International XENON GLADIATOR II, Инструкция по эксплуатации

Результаты поиска

Содержание XENON GLADIATOR II

Отзывы:

Похожие инструкции для XENON GLADIATOR II

Бренды по названию

Популярные бренды