Strebel S-HR 15 Скачать руководство пользователя

Страница: 31 / 33

Installation instructions S-HR series page 31

15 Error indication

A detected error is indicated on the display by means of blocking or error messages. A distinction should be made

between these two messages due to the fact that blocking can be of a temporary nature, however, error messages

are fixed lockings. The control will try its utmost to prevent locking and will temporarily switch off the unit by blocking

it. Hereunder is a list of some messages.

Blocks

with a number in the last 2 positions.

Block 01:

External safety contact cut off

Block 11:

Maximum

T of flow and return sensor in central heating has repeatedly been exceeded. During the

block normal operation of the hot water supply is possible. The pump continues to operate at minimum

capacity during the block.

Block 12:

Maximum

T of flow and return sensor in domestic hot water has repeatedly been exceeded. During

the block normal operation of the central heating installation is possible. During the block the pump

continues to operate at minimum capacity.

Block 60:

Incorrect parameter setting of the minimum or maximum power.

Block 67:

T has been detected between flow and return sensor whereas the burner is not in operation. After

the

T has disappeared the block will disappear.

Block 80:

Maximum flue gas temperature has been exceeded (if present). The block will not be cancelled until

the flue gas temperature has arrived below the temperature.

Block 81:

The flue gas sensor is not connected although it was connected to the control. The burner is blocked

until the flue gas sensor is reconnected.

Block 82:

The flue gas sensor has short-circuited, heat requirement blocked and pump capacity at minimum.

Block 85:

The control has not detected a water flow. The venting cycle is started. If during this cycle water flow

is detected, the venting cycle is ended and the burner is released.

Error

with a number in the last two positions.

Error 00: Poor flame-forming
Error 01: short-circuit of 24 volt circuit

Error 02: no flame-forming

Error 04: adjustment or error for voltage interruption
Error 05: adjustment

Error 12: fuse 24 volt/3AT faulty

Error 18: maximum flow temperature exceeded

Error 19: maximum return temperature exceeded
Error 28: number of revolutions not reported back from fan

Error 69: no or incorrect display

Error 80: maximum flue gas sensor temperature exceeded

Содержание S-HR 15


































Результаты поиска

Содержание S-HR 15

Отзывы:

Похожие инструкции для S-HR 15

Бренды по названию

Популярные бренды

Strebel S-HR 15, Руководство по установке

Результаты поиска

Содержание S-HR 15

Отзывы:

Похожие инструкции для S-HR 15

Бренды по названию

Популярные бренды