Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 327

background image

Commissioning

127

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

5.15

External operation for folding drawbar

Optional extra

WARNING

Risk of crushing, shearing and impact when moving the folding
drawbar!

Make sure that people leave the vicinity of the folding drawbar.

Always secure the drawgear by means of the holding-down device
before swivelling the supporting leg.

Use the two key buttons (1 and 2) on the left-
hand vehicle side in the side guard (3) to move
the folding drawbar with the hydraulic system
connected.

1.



Press the key button (1) to lift the vehicle
to the required height to adjust the
supporting leg.

2.



Press the key button (2) to lower the
vehicle.

Fig. 70

5.16

Mount extension sections, ropes and superstructure tarpaulin

WARNING

Risk of electrical shock or burns due to machine components
accidentally touching electrical overhead lines or approaching
high-voltage overhead lines in an inadmissible manner!

Make sure not to exceed the maximum vehicle height of 4 m.

Two people and a platform are required for mounting the
superstructure side panels, ropes and tarpaulin.

«
...
125
126
127
128
129
...
»

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Giga-Vitesse CFS 3602

Бренд: THORLABS Страницы: 44

Бренд: MacDon Страницы: 84

Бренд: MacDon Страницы: 89

Бренд: Patton electronics Страницы: 18

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

Бренд: Malmet Страницы: 14

Бренд: Zempire Страницы: 2

Бренд: FEAS Страницы: 72

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Datex-Ohmeda Страницы: 80

Бренд: MacDon Страницы: 2

Бренд: V-TAC Страницы: 6

Бренд: Varytec Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды