Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 327

background image

Commissioning

115

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

5.12.2.2 Load-sensing mode

1.

Always swivel the respective operating element at the control device on the tractor to floating
position.

2.

Turn the tractor engine off.

3.

Screw the load-sensing control line into the connecting aperture of the electro-hydraulic control
block.

4.

Screw the load-sensing screw (1) at the electro-hydraulic control block in as far as it will go.

5.

Connect the load-sensing control line to the load-sensing control system of the tractor.

6.

Connect the tank line (return line) to the free return port of the tractor provided for this purpose.

7.

Connect the pressure line (return line) with the pressure line to the hydraulic pump of the tractor
provided for this purpose.

5.12.3

Connect brake system

WARNING

Risk of crushing, cuts, becoming entangled, being drawn in
and risk of impact if the machine accidentally rolls due to the
service brake being released!

Always connect the hose coupling of the brake line (yellow) first and
then the hose coupling of the feed line (red).

The machine's service brake immediately comes off the brake
position if the red hose coupling is connected.

WARNING

Risk of crushing, cuts, becoming entangled, being drawn in
and risk of impact due to improper functioning of the brake
system!

Drain the air reservoir every day before the first trip.

Only start the tractor with the hitched machine moving when the
pressure gauge of the compressed-air brake system on the tractor
indicates 5.0 bar!

«
...
113
114
115
116
117
...
»

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Giga-Vitesse CFS 3602

Бренд: Pall Страницы: 51

Бренд: ZAMST Страницы: 21

Бренд: Bante Instruments Страницы: 6

Бренд: Taylor Страницы: 60

Бренд: TANDBERG Страницы: 23

Бренд: Backyard Play Systems Страницы: 73

Бренд: Rainin Instrument Страницы: 16

Бренд: V.ORLANDI Страницы: 144

Saturn 2000 GC/MS

Бренд: Varian Страницы: 9

Бренд: Zodiac Страницы: 2

Бренд: Zipper Mowers Страницы: 37

Бренд: Zimmer Страницы: 46

Бренд: Ultraflex Страницы: 52

Бренд: Palmgren Страницы: 12

Бренд: Bartscher Страницы: 20

Бренд: Bartscher Страницы: 61

Бренд: Barreto Страницы: 16

Бренд: Parkside Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды