Stratus SAE-F10P Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 43

Stratus SAE-F10P Скачать руководство пользователя страница 4

STRATUS Floor Plate 2 post Lift Installation & Operation & Maintenance Instructions

4

Foreword

Notes on the operating instructions

The present ORIGINAL OPERATING INSTRUCTIONS are designed to provide sufficient instruction for the

safe operation of the product. The information is provided clearly and concisely. The chapters are arranged by
letter and the pages are numbered continuously.

Our products are subject to ongoing development. Our company reserves the right to alter the design,
equipment and technical features of the system. No guarantee of particular features of the product should
therefore be assumed from the present operating instructions.

Safety notices and text mark-ups

Safety instructions and important explanations are indicated by the following graphics:

Indicates an extremely hazardous situation. Failure to comply with this instruction will result in
severe irreparable injury and even death.

Indicates an extremely hazardous situation. Failure to comply with this instruction may result in
severe irreparable injury and even death.

Indicates a hazardous situation. Failure to comply with this instruction may result in

slight to medium injury.

Indicates a material hazard. Failure to comply with this instruction may result in material damage.

«
...
2
3
4
5
6
...
»

Содержание SAE-F10P












































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды