STOVES 720G Скачать руководство пользователя страница 38

Страница: 38 / 43

7. Oven door glass panels

a. Open the door and insert 2 screws

through  the  inner  holes  in  the  door
hinge  arms  (to  stop  the  door  from
springing  up  when  you  remove  the
outer glass panel).

b. Slide out the inner glass panel.

Important:

The inner glass panel

must be replaced the right way up (so
the reflective side faces the outer glass
panel) and pushed fully in to the stop
position.

Hold the door handle as you unscrew
the 2 corner screws through the door frame.

d. Remove the outer glass panel by

carefully pulling towards you.

8. Programmer / clock

a. Disconnect the electricity supply.
b. Remove the facia glass panel (2).
c.

Disconnect the leads from the back of
the programmer.

d. Ease the PCB programmer off its supports.

9. Thermostat

a. Remove appliance from housing (1).
b. Unscrew the top / rear panel securing

screws. Ease the panel backwards,
remove both fan leads & lift panel clear.

Remove the fascia glass panel (2).

d. From inside oven, unclip the thermostat

phial & feed out through the hole.

e. Disconnect the outlet tubing connections

from the thermostat and the grill tap.

Remove the 2 screws securing the gas
rail support bracket to the front frame.

g. Remove the 2 screws securing the gas

rail inlet pipe to the rear panel and lift
the gas rail assembly away from the
appliance.

h. Remove the 2 screws through the

thermostat bracket.

10. FSD

a. Remove appliance from housing (1).
b. Unscrew the top / rear panel securing

screws.  Ease  the  panel  backwards,
remove  both  fan  leads  and  lift  panel
clear.    From  inside  the  oven  remove
the oven burner (13).

d. Pull off the injector carrier positioning

clip at RHS of oven burner bracket.

e. Disconnect inlet pipe from FSD valve,

this can now be removed complete
with the injector carrier and probe.

Note:

When replacing the injector

carrier make sure the positioning clip
is located into the groove.

11. Grill tap

a. Remove appliance from housing (1).
b. Unscrew the top / back panel secur-

ing screws. Ease the panel back-
wards, remove both fan leads and lift
panel clear.

Remove the fascia glass panel (2).

d. Disconnect outlet tubing connections

from the thermostat and the grill tap.

e. Remove the two screws securing the

gas rail support bracket to the front
frame.

Remove the 2 screws securing the gas
rail inlet pipe to the rear panel and lift
the gas rail assembly away from the
appliance.

g. Remove the 2 screws through the grill

tap bracket.

SERVICING INSTRUCTIONS

Содержание 720G












































Результаты поиска

Содержание 720G

Отзывы:

Похожие инструкции для 720G

Бренды по названию

Популярные бренды

STOVES 720G, Инструкция для пользователя, установки и обслуживания

Результаты поиска

Содержание 720G

Отзывы:

Похожие инструкции для 720G

Бренды по названию

Популярные бренды