17
16
7. CO M MIS S IO NIN G A N D O PER ATIO N
Connecting the Vaporizer using the power
adapter or 12 volt Car Charger
Once the charging operation is com-
plete, first disconnect the power adapt
-
er from the mains socket and then un-
plug from the Vaporizer.
The CRAFTY cannot be oper-
ated while plugged in. It can
only be turned on again if it has
been partially charged beforehand.
The battery can also be
charged via the optional 12
volt Car Charger. Connect the
12 volt Car Charger to the power sock-
et of the Vaporizer using the USB cable
and then plug the Car Charger into the
socket in the car for the cigarette light-
er, or any other suitable 12 V socket.
Charge and complete the operation in
the same way as with the power adapt-
er (see Chapter 7.1. “Charging the Bat-
tery”, page 16).
Batteries are specially assem-
bled consumable items that
can only be replaced by Storz
& Bickel when the CRAFTY
Vaporizer
is sent in to them.
Any attempt by the customer to re-
place the battery by him/herself is po-
tentially dangerous and leads to loss of
any claims under the warranty and ex-
empts Storz & Bickel from any liability.
Automatic Switching Off
The automatic switching off is used to
save battery capacity so that the Va
-
porizer can be used as long as possible
without charging.
The device switches off automatically
one minute after the last press of a but-
ton or the last application. The switch-
ing off of the Vaporizer is indicated by
a short vibration and by displaying the
charged state.
A short press of the ON/OFF
switch during operation can
reset the automatic switching-
off to one minute.
7. CO M MIS S IO NIN G A N D O PER ATIO N
Do not leave the device unat-
tended during operation.
Place the CRAFTY
Vaporizer
only on a hard, heat-resistant, flat, sta
-
ble surface, never on soft surfaces or
flammable material. Check whether
the power supply voltage corresponds
to the voltage rating listed on the pow-
er adapter. The power adapter and USB
cable must be in perfect condition.
Connect the power adapter only to a
properly installed socket.
The manufacturer will not bear any
responsibility whatsoever if this acci-
dent prevention measure is not taken.
Please unplug the power adapter from
the mains socket to completely discon-
nect from the mains power supply.
7.1. Charging the Battery
The battery charge status is signaled
by the blue light on the LED display.
Explanations on the battery display
during the charging operation:
Steady blue light:
the battery is fully charged.
Blue, slow-flashing light: the battery
is between 61 and 96% charged
Blue, rapidly flashing light: the battery
is between 31 and 60% charged
Blue flashing: the battery is up to 30%
charged
Explanations of the battery display fol-
lowing switch off:
Steady blue light: the battery is
between 64 and 100% charged
Blue, slow-flashing: the battery is
between 32 and 64% charged
Blue, rapidly flashing: the battery is
between 1 and 32% charged
Blue flashing: battery is completely
discharged
Check the housings of the Va
-
porizer and the power adapter
for signs of damage each time
before using or charging. The Vaporiz
-
er may not be charged and neither Va
-
porizer nor power adapter used if these
are damaged.
The battery charge of the new product
has a level of up to 80%. Fully charge
before using for the first time.
The charging time for the battery de-
pends on how old it is and how high
the charge is on starting; it takes about
two hours if the battery is completely
discharged.
Connect the USB cable to the charg-
ing socket of the Vaporizer and to the
power adapter. Then plug the power
adapter into a suitable power socket.
Note: When the power adapter is
plugged into the mains, the LED dis-
play lights up in green/red/blue for a
moment and the Vaporizer vibrates
briefly. This serves as a functional
check and indicates that the charging
operation has started.
The LED lights up and starts to flash,
i.e. the battery is being charged. As
soon as the battery is fully charged,
the charge indicator lamp stops flash
-
ing and shows a steady blue light.
