STORK TRONIC ST48-WHDVM.04 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 20

STORK TRONIC ST48-WHDVM.04 Скачать руководство пользователя страница 20

Order No.: 141648

Technical data of ST48-WHDVM.04

Measuring input

F1:

Sensor following value

F2:

Sensor leading value

Sensor type Resistance thermometer Pt100

Measuring range: -99°C...+750 °C

Measuring accuracy at 25°C: +/-0.5K +/-0.5% of measuring range

Outputs
K1:

Relay, normally-open contact, 8(1,5)A 28V, function see parameter U1

K2:

Relay, normally-open contact, 8(1,5)A 28V, function see parameter U2

K3:

Relay, normally-open contact, 8(1,5)A 28V, function see parameter U3

Installed buzzer, ca. 85dB

Analogue output
S1:

linear voltage output 0...+10V

Display

One 3-digit LED-display, height 13mm, colour red
One 4-digit LED-display, height 10mm, colour red
Three LEDs, for status display of the outputs K1, K2, K3.

LON communication interface

shielded 2-wire line, Twisted Pair, 78kBaud, not polar, maximum cable length 100m
Interface driver: RS485, galvanically not separated.
The network has to be installed in line topology and terminated with 120Ohm at each side.

Power supply

12-24V AC +/-10%(50/60Hz) or 16-36V DC
Power consumption max. 3VA

Connectors

Plug and socket
Clamp A:

8-pole, spacing 5,0mm, for cable up to 2.5 mm²

Clamp B:

11-pole, spacing 3.5 mm, for cable up to 1.5 mm²

Ambient conditions:

Storage temperature:

-20...+70°C

Operating temperature:

0...+55°C

Relative humidity:

max. 75% without dew

Weight

ca. 130g

Enclosure

Front IP65, IP00 from back

Installation data

Unit is to be installed in an instrument panel.
Front size:

48 x 48 mm

Panel cut-out:

45.2 x 45.2 mm

Installation depth:

ca. 120 mm

Mounting by fixing strap.

«
...
18
19
20

Содержание ST48-WHDVM.04





















Отзывы:

Нет отзывов