background image

 

 

 

SPECIFICATION 

 

 

Width:22  Length: 24  Height: 11 ft 

 

IMPORTANT ---- READ MANUAL FIRST 

 

 

Improper  site  preparation,  Assembly  and  Maintenance  may  invalidate  warranty  and 
cause  unnecessary  and  costly  mistake.  If  you  have  any  questions  contact  your  local 
dealer. 

 

For user friendly assembly we have identified each individual component with the part 
code as indicated in the parts list. Please refer to the part code numbers and drawing to 
ensure problem free assembly. 

 

It’ s necessary to tighten the roof fabric enough to avoid “ hammocks” on the roof  and 
also re-tighten once or twice again after a few months of use. This is important when 
assembly in cold weather (autumn and winter) because the fabric is stiff then and when 
we  got  the  sun  and  warm  weather  afterwards  it  will  make  the  fabric “ slack” 
again and need to be re-tighten before next winter. 

 

It’ s the owners responsibility to take of snow immediately if not slide off by itself. 

 

 

READ ALL INSTRUCTIONS BEFORE ASSEMBLY 

1.

 

Keep work area clean. Cluttered areas invite injuries. Do not set up near snow 
drifts, in slippery places, in high winds, or wet location. 

2.

 

Keep children away. All children should be kept away from the work area. 

3.

 

Don’ t over reach. Keep proper footing and balance at all times. 

4.

 

Do not assemble in under the influence of alcohol or drugs. Read warning labels on 
prescriptions to determine if your judgment or reflexes are impaired while taking 
drugs. If there is any doubt, do not assemble. 

5.

 

Be  aware  of  possible  windy  conditions;  fasten  the  bases  in  concrete  if  these 
conditions are likely to occur. Remove the cover during hurricane. 

6.

 

Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. 
Do not expose to open flame. 

7.

 

Be aware of personal safety during assembly and use. Be carful not to pinch fingers 
with  clips  and  tubes  when  assembling:  when  using  makes  sure  there  is  adequate 
ventilation for exhaust and other dangerous fumes. 

Содержание Two Car Garage Shelter










Отзывы: