background image

4

866-795-1586 • WWW. STONEAGETOOLS.COM

WARNING AND SAFETY INSTRUCTIONS

WARNING 

Operations with this equipment can be potentially hazardous. Caution must be exercised prior to and 
during machine and water jet tool use. Please read and follow all of these instructions, in addition to the 
guidelines in the WJTA Recommended Practices handbook, available online at 

www.wjta.org

. Deviating 

from safety instructions and recommended practices can lead to severe injury and/or death.

•  Do not exceed the maximum operating pressure specified for any component in a system. The 

immediate work area must be marked off to keep out untrained persons.

•  The 

Dump Valve 

is the most important safety device. Each operator must have and be able to use their 

own Dump Valves to shut down the water pressure immediately if necessary.

•  Inspect the equipment and nozzles for visible signs of deterioration, damage, and improper assembly. 

Do not operate until repaired. Make sure all threaded connections are tight and free of leaks.

•  All operators and persons in close proximity must wear personal protective equipment, including 

approved protection for body, hands, feet, face, ears, eyes, and air passages. Please refer to the WJTA 
Recommended Practices, Section 6. 

•  Water pressure greater than 20,000 psi (1379 bar) can reach 200oF (93oc) and can scald or burn the 

operator. Always use face shields, water jet resistant armor, and gloves to protect the operator from 
being burned or cut.

•  The use of gloves when handling the tool after operation is recommended as the body at the pulling ring 

end may reach temperature of up to 160°F.

•  Inspect the high pressure hose for damage. Use ONLY hoses intended for waterblast applications and 

rated for the maximum operating pressure on the job. The high pressure hose should be as large as 
possible to minimize pressure loss through the hose. 

DANGER

BOTH THE TR-130 AND TR-200 MODELS OF TORUS CONTAIN SEVERAL HIGH-ENERGY, RARE-

EARTH MAGNETS THAT PRODUCE A MAGNETIC FIELD IN EXCESS OF 10 GAUSS. PERSONS WITH 

A PACEMAKER OR OTHER ELECTRONIC MEDICAL DEVICE MUST USE EXTREME CAUTION WHEN 

HANDLING, OR IN CLOSE PROXIMITY TO THE TORUS.  IT IS RECOMMENDED THAT A MINIMUM 

DISTANCE OF 6 INCHES (152MM) BE MAINTAINED AT ALL TIMES BETWEEN THE TORUS AND ANY 

ELECTRONIC MEDICAL DEVICES.

Содержание TORUS TR-130





































Отзывы: