background image

Safety Alert Symbol:

This symbol 

Indicates danger, warning or caution.

Attention is required in order to avoid serious personal
injury. The message that follows the symbol contains
important information about safety.

Signal Word:

Signal words are

 distinctive words used throughout

this manual that alert the reader to the existence
and relative degree of a hazard.

 

 

CAUTION

The signal word “CAUTION” 

indicates a potentially

hazardous situation, which, if not avoided, may result
in minor or moderate injury and equipment/property
damage.

A Few Words About Safety

Safety Information

 Read and understand the entire manual before
operating or maintaining Stoelting equipment.

This Owner's Manual provides the operator with
information for the safe operation and maintenance of
Stoelting equipment. As with any machine, there are
hazards associated with their operation. For this
reason safety is emphasized throughout the manual.
To highlight specific safety information, the following
safety definitions are provided to assist the reader.

The purpose of safety symbols is to attract your
attention to possible dangers. The safety symbols, and
their explanations, deserve your careful attention and
understanding. The safety warnings do not by them-
selves eliminate any danger. The instructions or
warnings they give are not substitutes for proper
accident prevention measures.

If you need to replace a part, use genuine Stoelting
parts with the correct part number or an equivalent
part. We strongly recommend that you do not use
replacement parts of inferior quality.

 

 

WARNING

The signal word “WARNING” indicates a potentially
hazardous situation, which, if not avoided, may result
in death or serious injury and equipment/property
damage.

CAUTION

The signal word “CAUTION” not preceded by the
safety alert symbol indicates a potentially hazardous
situation, which, if not avoided, may result in equip-
ment/property damage.

NOTICE

The signal word “NOTICE” indicates information or
procedures that relate directly or indirectly to the
safety or personnel or equipment/property.

Содержание Futura F131






































Отзывы: