Stobag MOVENO DSRCE-V, Инструкции по установке и использованию, предупреждения, Страница: 31 / 44

www.stobag.com
GB
31
5.1) Available transmitters
Table A8 indicates the transmitters that can be used.
The MOVENO DSRCE-V motors recognise other SKIMY and SKIROSOL SRCK 610 series transmitters (see chapter 5.1 “Available transmit-
ters”).
Warning: use transmitters that have been memorised in Mode 1 only for programming.
5) Additional information
Transmitters
SKIMY SRCH
SKIMY SRCW
SKIROSOL SRCK 610, 620, 630
SKIMY SRCU
Table “A8”
As for the installation, the disposal of the product at the end of its
effective life, must be performed by qualified personnel.
This product is made of various types of material, some of which can
be recycled while others must be disposed of. Enquire about the
recycling or disposal systems available for this product category in
compliance with regulations locally in force.
Warning: some parts of the product may contain polluting or haz-
ardous substances that, if incorrectly disposed of, could have a dam-
aging effect on the environment or on the health of individuals.
As indicated by the symbol, this product
must not be disposed of in household waste.
Perform “separated collection” for disposal in
compliance with regulations locally in force,
or return the product to the manufacturer
when purchasing a replacement.
Heavy fines may be imposed by local laws for the illegal disposal of
this product.
6) Disposal
The 2 beeps are not heard after the motor has been
switched on and the Step-by-Step does not command any
operations.
Check that the motor is supplied with the foreseen mains power sup-
ply. If the power supply is correct there could be a serious fault and
the motor needs to be replaced.
6 beeps are heard after a remote control command is sent
and the manoeuvre does not start.
The remote control is not synchronised therefore the transmitter
needs to be memorised again.
10 beeps are heard after a command and the manoeuvre
starts.
The self-diagnosis of the parameters in the memory has detected a
fault (positions, TTBUS address, wind and sun level, movement direc-
tion incorrect). Check and if necessary repeat the programming.
The motor does not move after a command is given.
• The thermal cutout may have tripped, therefore wait for the motor
to cool.
• It may be that the set threshold has been exceeded if a wind sensor
has been installed.
• Otherwise, try turning the motor on and off. If 2 beeps are not heard
it may be that the motor has a serious fault and therefore needs
replacing.
The motor stops before reaching the foreseen opening
position (pos. “0”, pos. “I”) and attempts to start again
twice.
This is normal if the programming of the “0” and “1” positions has
been performed in the SEMI-AUTOMATIC mode: in case of overload
during the opening manoeuvre, the motor is turned off for approxi-
mately 1 second and then attempts to complete the manoeuvre.
Check if there are any obstacles preventing the manoeuvre.
The motor stops before reaching the foreseen opening or
closing positions (pos. “0”, pos. “I”, pos. “1”).
This is normal: in case of overload the motor is turned off. Check if
there are any obstacles preventing the manoeuvre.
The motor moves only in the “hold-to-run” mode.
If the “0” and “1” have not been programmed the opening and clos-
ing manoeuvre of the motor occur in hold-to-run only. Program the
“0” and “1” positions.
The “0” and “1” positions have been programmed but the
closing manoeuvre has a hold-to-run movement.
The self-diagnosis of the parameters in the memory has detected a
fault in the motor’s position. Give the awning an up command and
wait for it to reach the “0” position.
7) What to do if…
a short troubleshooting guide!
SKIMY SRCH SKIMY SRCW SKIMY SRCU SKIROSOL SRCK 610
MOVENO_DSRCE-V.indd 31 MOVENO_DSRCE-V.indd 31 9.2.2010 14:33:53 Uhr 9.2.2010 14:33:53 Uhr