manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

LS_JPEG codec

Doc ID 018672 Rev 1

565/844

25.4.10 JPGC 

bytes 

from core to Fifo register

This register contains the number of bytes that have been sent, at a given time, from the 
codec core to the FIFO Out buffer. The content of this register is cleared automatically when 
a new coding process starts.

         

●

NTX

Number of bytes sent from the Codec Core to FIFO Out. This register is cleared when 
a new encoding process starts.

25.4.11 

JPGC bust count beforeInit

This register contains the number of burst transfer sent by TX FIFO before controller will set 
interrupt. It's ignored if burst count ENABLE bit is 0. 

         

●

EN

Burst Count Enable, Active High.

●

BTF

Number of burst transfer sent by TX FIFO before controller will set interrupt.

25.4.12 DMAC 

registers

See 

Chapter 19: BS_DMA controller

, for a detailed description of the DMAC registers.

25.4.13 JPGCFifoIn 

register

This register is used to read data from, or write data to, the FIFO In, which is used to 
bufferize the transfers from the external RAM to the codec core, under the control of the 
codec controller.

Table 480.

JPGC bytes from core to Fifo register bit assignments

Bit

Name

Reset 
Value

Description

[31:00]

NTX

-

Number of bytes from codec core to FIFO out.

Table 481.

JPGCbust Count before Init register bit assignments

Bit

Name

Reset 
Value

Description

[31]

EN

-

Burst Count ENABLE, active high

[30:00]

BTF

-

Number of burst transfer send by TX FIFO before interrupt.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

ABB 650 series Engineering Manual preview
650 series
Бренд: ABB Страницы: 128
Gardena 4030 Operator'S Manual preview
4030
Бренд: Gardena Страницы: 16
MADRIX STELLA Technical Manual & Quick Start Manual preview
STELLA
Бренд: MADRIX Страницы: 28
Hach sc200 Software Update preview
sc200
Бренд: Hach Страницы: 2
Hach ORBISPHERE 410 Quick Operator'S Manual preview
ORBISPHERE 410
Бренд: Hach Страницы: 12
Hach AS950 AWRS Basic Operations preview
AS950 AWRS
Бренд: Hach Страницы: 472
Hach sc1000 User Manual preview
sc1000
Бренд: Hach Страницы: 64
Hach SC4500 Basic User Manual preview
SC4500
Бренд: Hach Страницы: 210
Samwontech TEMP2000 Series Installation Manual preview
TEMP2000 Series
Бренд: Samwontech Страницы: 91
YASKAWA U1000 iQpump Drive User Manual preview
U1000 iQpump Drive
Бренд: YASKAWA Страницы: 426
YASKAWA Motoman DX200 Safety Notes preview
Motoman DX200
Бренд: YASKAWA Страницы: 26
YASKAWA motoman NX100 Instructions Manual preview
motoman NX100
Бренд: YASKAWA Страницы: 210
YASKAWA Z1000 CIMR-ZU*A Series User Manual preview
Z1000 CIMR-ZU*A Series
Бренд: YASKAWA Страницы: 400
YASKAWA Z1000 CIMR-ZU*A Series Technical Manual preview
Z1000 CIMR-ZU*A Series
Бренд: YASKAWA Страницы: 466
Daikin BRC1H61W Installation Manual preview
BRC1H61W
Бренд: Daikin Страницы: 46
Daikin BRC1H61W Installation Handbook preview
BRC1H61W
Бренд: Daikin Страницы: 26
Watts KONTACT Manual preview
KONTACT
Бренд: Watts Страницы: 17
Linear Technology LT8570 Demo Manual preview
LT8570
Бренд: Linear Technology Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды