STK Professional Audio VM-8DRV, Руководство пользователя

Страница: 6 / 32

6
4a. EFX(DSP)
The channel EFX(DSP) control varies the amount of channel
signal sent to the D.S.P, as well as to the effects send circuitry.
5a. MON
This controls the amount of signal sent from an individual
channel to both the Mon master control.
In addition, this control also feeds the monitor send.
This aux send is a pre channel level control and pre EQ. This
means that the level sent from an individual input will not be
affected by adjustment of the main channel level control or EQ
settings and allows a completely separate mix for stage
monitors.
6a. High
The high frequency shelf control is set at 8kHz. You can
increase or attenuate frequencies 8kHz(and above)up to 15dB.
There is a detente in the 0 position indicating a flat response
.
7a. Mid
The mid frequency is centered at 2.5 kHz.
You can increase or attenuate the midrange
frequencies by as much 12dB. A detente is provided
in the 0 position indicating a flat response.
8a. Low
The low frequency shelf control is set at 80Hz. You can
increase or attenuate frequencies 80Hz(and below) up to 15dB.
A detente is provided in the 0 position indicating a flat
response.
9a. Bal
This control varies the amount of channel signal sent to either
the left or right channel of the stereo mixer.
FRONT PANEL MASTER SECTION
11. Aux In
Connect these jacks to he output jacks of an external effects
processor. If the effects processor has a stereo output,
connect it to the AUX IN L(MONO) and R jacks. If it has
monaural output, use the AUX IN L(MONO) jack. Signal input to
these jacks is sent to the ST bus
.
12. Tape In
Use these jacks to connect a stereo device, such as a cassette
player or a CD player. The signals input to these jacks is sent
to the ST bus
.
13. Rec Out
The ST bus signal before it has passed through the MASTER
control and graphic equalizer.
14. Monitor Out
The MONI bus signal which has passed through the MASTER
control and graphic equalizer.
15. Main L/R Out
The ST bus signal which has passed through the main MASTER
control and graphic equalizer
.
16. EFX Out
The input of an external effect such as a delay or echo can be
connected to this jack. The signal adjusted by the EFFECT
control of each channel will be sent to the EFFECT bus, its
level adjusted by the EFFECT OUT control , and output from
this jack.
17. Footswitch
The DSP Footswitch jack is a standard 1/4
＂
size
accommodating a monaural ON/OFF Footswitch that
enables/disable the internal digital effects.
18. Mono/Subwoofer
This line level subwoofer output allows you to conveniently
add
supplemental buss to your system. The signal is derived from
summed left+right master output or the master output and is
routed through a 125Hz low pass filter.
19. Aux In /Tape In Control
This control varies the amount of the signal from the
Tape In and Aux In mixed back to the main buss.
20. Aux / Tape to Mon Control
The Aux/Tape to Mon Control provides continuously variable
adjustment of the signal derived from the tapein jacks located on
the connector panel and sends that signal to the monitor/aux
master control
.
21. Main Amp Assign (L+R/Bridge, Stereo)
This slide switch select a signal route depending on the
speakers connected to the speaker L,R/L+R bridge jacks on
the rear panel.
22. Master Monitor Control
This controls the overall signal level at the Monitor Line Out.
This setting is output to both the front and rear panel monitor
jacks and appears in the monitor bus signal.
23. DSP Switch
This push control activates/deactivates the DSP effects.
24. EFX to Mon
This master EFX control varies the amount of
overall combined signal of the independent channels
sent to the Monitor EFX bus.
Panel Descriptions