Still RCD15 Скачать руководство пользователя

Страница: 112 / 176

General information

To keep the forklift truck in a good operating

condition, the repair work specified on the fol-

lowing pages must be carried out regularly, at

the indicated intervals, and using the consum-

able material designed for the purpose. A writ-

ten record must be kept of all work that has

been carried out. This is the only way of guar-

anteeing validity of the warranty.

CAUTION

Any upcoming maintenance and repair work must be

carried out by authorised service engineers in order

to guarantee that the truck remains in a good, safe

operating condition and that it fulfils all technical

specifications.

CAUTION

The intervals for the various maintenance tasks to be

carried out on a regular basis must be shortened ac-

cordingly if the truck is used in particularly severe

conditions, such as:

–

In dusty environments

–

At temperatures below zero

–

For particularly heavy-duty work

To determine the amended maintenance intervals,

please contact your authorised service centre.

NOTE

Please contact your authorised service centre

for a maintenance contract that is appropriate

for your forklift truck.

Maintenance

General information

102

60098011601 EN - 08/2020

Содержание RCD15

















































































































































































Результаты поиска

Содержание RCD15

Отзывы:

Похожие инструкции для RCD15

Бренды по названию

Популярные бренды

Still RCD15, Оригинальное руководство пользователя

Результаты поиска

Содержание RCD15

Отзывы:

Похожие инструкции для RCD15

Бренды по названию

Популярные бренды