Still RCD15 Скачать руководство пользователя

Страница: 103 / 176

WARNING

Excessive water pressure or water and steam that

are too hot can damage truck components.

–

Strictly adhere to the following steps.

–

Only use high-pressure cleaners with a

maximum output power of 50 bar and at a

maximum temperature of 85°C.

–

When using high-pressure cleaners, make

sure there is a distance of at least 20 cm

between the nozzle and the object being

cleaned.

–

Do not aim the cleaning jet directly at adhe-

sive labels or information signs.

DANGER

Risk of fire! Deposits/accumulations of

combustible materials may ignite in the

vicinity of hot components (e.g. exhaust

pipes).

–

Strictly adhere to the following steps.

–

Regularly remove all deposits/accumula-

tions of foreign materials in the vicinity of

hot components.

–

Do not place combustible materials in the

engine compartment.

DANGER

Risk of fire! Flammable fluids can be ig-

nited by hot components on the truck.

–

Strictly adhere to the following steps.

–

Do not use flammable fluids for cleaning.

–

Observe the manufacturer's guidelines for

working with cleaning materials

CAUTION

Abrasive cleaning materials can damage component

surfaces!
Using abrasive cleaning materials that are unsuitable

for plastics may dissolve plastic parts or make them

brittle. The screen on the display operating unit may

become cloudy.

–

The procedures outlined below must be followed

in all cases.

Use and operation

Cleaning

60098011601 EN - 08/2020

Содержание RCD15

















































































































































































Результаты поиска

Содержание RCD15

Отзывы:

Похожие инструкции для RCD15

Бренды по названию

Популярные бренды

Still RCD15, Оригинальное руководство пользователя

Результаты поиска

Содержание RCD15

Отзывы:

Похожие инструкции для RCD15

Бренды по названию

Популярные бренды