Stihl TS 500i Скачать руководство пользователя страница 90

Страница: 90 / 118

TS 500i

Remove the support foot (1) from
the retainers (arrows) and pull it
out of the guide on the tank
housing on the side of the tank
filler port

Remove support foot (1) with air
baffle (2)

Pull support foot (1) out of the
guide (arrow) of the air baffle (2)
and examine it, replace if
necessary

1307RA344 TG

1307RA345 TG

1307RA346 TG

Pry the stop buffer (1) out of the
holes of the air baffle (2)

– Check the wiring harness of the

solenoid valve, replace if
necessary,

9.6.3

Installation

– Apply STIHL press fluid to the

peg of the stop buffer,

Push stop buffer (1) into the
holes of the air baffle (2) and
drawing in on the pegs (arrows)
until they enclose the holes
completely

1307RA347 TG

1307RA348 TG

– Apply STIHL press fluid to the

guide of the support foot,

Push the support foot (1) into the
guide (arrow) of the air baffle (2)

Position the air baffle (1) and
support foot (2) so that the
peg (3) engages behind the
opening and the tab (4) is over
the guide of the wiring harness
– Do not pinch wiring harness

1307RA349 TG

1307RA350 TG

Содержание TS 500i























































































































Результаты поиска

Содержание TS 500i

Отзывы:

Похожие инструкции для TS 500i

Бренды по названию

Популярные бренды

Stihl TS 500i, Руководство по обслуживанию

Результаты поиска

Содержание TS 500i

Отзывы:

Похожие инструкции для TS 500i

Бренды по названию

Популярные бренды