Stihl TS 500i Скачать руководство пользователя страница 84

Страница: 84 / 118

TS 500i

Antivibration elements

The handle frame, tank housing and
engine housing are connected by
vibration-damping springs.

Damaged springs must be replaced
as a matter of principle.

9.1

Antivibration spring on
handlebar

The antivibration spring is located
between handlebar and crankcase
on the clutch side and must be
replaced if defective.

– Remove the muffler,

6.1

Unscrew screw (1) and remove
clamp (2)

Unscrew screw (1) and remove
antivibration spring (2)

1307RA021 TG

1307RA031 TG

Unscrew handlebar support (1)

– Examine the spring, handlebar

support and clamp, replace if
necessary

Installation

Screw the handlebar support (1)
into the antivibration spring (2) as
far as possible (arrow)

Fit the antivibration spring with
handlebar support (arrow) on the
handlebar and hold it in position

370RA253 TG

370RA254 TG

370RA255 TG

Fit the clamp (1) on the opposite
side so that the guide (arrow) is
on the inside of the handlebar

Insert a screw (2) through the
clamp and handlebar, and screw
it tightly into the opposite
handlebar support (3)

Push antivibration spring (1) into
the mount (arrow) with the
serration of the bearing plug

1307RA032 TG

1307RA033 TG

Содержание TS 500i























































































































Результаты поиска

Содержание TS 500i

Отзывы:

Похожие инструкции для TS 500i

Бренды по названию

Популярные бренды

Stihl TS 500i, Руководство по обслуживанию

Результаты поиска

Содержание TS 500i

Отзывы:

Похожие инструкции для TS 500i

Бренды по названию

Популярные бренды