Stihl MS 391 Скачать руководство пользователя

Страница: 39 / 68

MS 311, MS 391

English

Fuel filler cap

Before fueling, clean the cap and
the area around it to ensure that no
dirt falls into the fuel tank

Always position the machine so that
the cap is facing upwards

Opening

Swing the clip into an upright
position

Turn the cap counterclockwise
(approx. 1/4 turn)

Remove fuel filler cap

Refueling

Take care not to spill fuel while fueling
and do not overfill the tank.

STIHL recommends use of the STIHL
filling system for fuel (special
accessory).

Refueling

Closing

Clip is in an upright position:

Fit the cap – position marks on the
cap and the filling port must line up

Push the cap down as far as it will
go

Hold the cap down and twist it
clockwise until it engages

Fold down the clip as far as it will go

Fueling

001BA229 KN

001BA218 KN

001BA219 KN

001BA224 KN

001BA220 KN

001BA221 KN

001BA222 KN

Содержание MS 391





































































Результаты поиска

Содержание MS 391

Отзывы:

Похожие инструкции для MS 391

Бренды по названию

Популярные бренды

Stihl MS 391, Руководство по безопасности

Результаты поиска

Содержание MS 391

Отзывы:

Похожие инструкции для MS 391

Бренды по названию

Популярные бренды