Stihl HS 56 Скачать руководство пользователя страница 9

Страница: 9 / 24

4.2.4

Examples

Quantity of gaso‐

line

STIHL two-stroke

engine oil 1:50

Liters

(ml)

0.02

(20)

0.10

(100)

0.20

(200)

0.30

(300)

0.40

(400)

0.50

(500)

► Pour oil into an approved safety fuel canister

first, then add gasoline and mix thoroughly

4.3

Storing fuel mixture

Store in approved safety fuel canisters only in a

dry, cool and secure place protected against light

and sunlight.
Fuel mixture deteriorates with age – mix only as

much as needed for a few weeks. Do not store

fuel mixture for longer than 30 days. The fuel

mixture can become unusable more quickly if

exposed to light, sunlight or low or high tempera‐

tures.
STIHL MotoMix however can be stored for up to

5 years without any problems.

► Shake the canister containing the fuel mixture

thoroughly before refueling

WARNING

Pressure may have built up in the canister –

open it carefully.
► The fuel tank and the canister in which fuel

mixture is stored should be cleaned thoroughly

from time to time

Residual fuel and the liquid used for cleaning

must be disposed of in accordance with regula‐

tions and without harming the environment!

Fueling

5.1

Preparations

0008BA025 KN

► Before fueling, clean the filler cap and the area

around it to ensure that no dirt falls into the

tank.

► Position the machine so that the filler cap

faces up.

5.2

Opening

001BA236 KN

► Raise grip to vertical position.

001BA232 KN

► Turn the cap counterclockwise (about a quar‐

ter turn).

5 Fueling

English

0458-447-8321-D

Содержание HS 56

























Результаты поиска

Содержание HS 56

Отзывы:

Бренды по названию

Популярные бренды

Stihl HS 56, Инструкция по эксплуатации

Результаты поиска

Содержание HS 56

Отзывы:

Бренды по названию

Популярные бренды