Stihl HS 56 Скачать руководство пользователя страница 15

Страница: 15 / 24

11 Checking the Spark Plug

► If the engine is down on power, difficult to start

or runs poorly at idle speed, first check the

spark plug.

► Fit a new spark plug after about 100 operating

hours – or sooner if the electrodes are badly

eroded. Install only suppressed spark plugs of

the type approved by STIHL – see "Specifica‐

tions".

11.1

Removing the Spark Plug

► Stopping the Engine

0008BA017 KN

► Carefully pry open the flap (1) with a suitable

tool (e.g. combination wrench).

0008BA018 KN

► Remove the spark plug boot (2) using a suita‐

ble tool (e.g. combination wrench).

► Unscrew the spark plug.

11.2

Checking the Spark Plug

000BA039 KN

► Clean dirty spark plug.

► Check electrode gap (A) and readjust if neces‐

sary – see "Specifications".

► Rectify the problems which have caused foul‐

ing of the spark plug.

Possible causes are:

–

Too much oil in fuel mix.

–

Dirty air filter.

–

Unfavorable running conditions.

000BA045 KN

WARNING

Arcing may occur if the adapter nut (1) is loose

or missing. Working in an easily combustible or

explosive atmosphere may cause a fire or an

explosion. This can result result in serious inju‐

ries or damage to property.
► Use resistor type spark plugs with a properly

tightened adapter nut.

11.3

Installing the Spark Plug

► Insert and screw home the spark plug by

hand.

► Tighten down the spark plug.

► Press the spark plug boot firmly onto the spark

plug.

0008BA019 KN

► Close the flap (1), top first, then the bottom,

tabs (arrows) must snap into position.

11 Checking the Spark Plug

English

0458-447-8321-D

Содержание HS 56

























Результаты поиска

Содержание HS 56

Отзывы:

Бренды по названию

Популярные бренды

Stihl HS 56, Инструкция по эксплуатации

Результаты поиска

Содержание HS 56

Отзывы:

Бренды по названию

Популярные бренды