Stihl HS 56 Скачать руководство пользователя страница 14

Страница: 14 / 24

Cleaning the Air Filter

8.1

If there is a noticeable loss of

engine power

0008BA014 KN

► Loosen the captive screw (1) and remove the

filter cover (2).

► Clean away loose dirt from around the filter.

► Remove the filter element (3).

► Fit a new filter element. As a temporary meas‐

ure you can knock it out on the palm of your

hand or blow it out with compressed air. Do

not wash.

► Replace any damaged parts.

► Fit the filter element (3).

► Fit the filter cover (2) and screw it down firmly.

Adjusting the Carburetor

The carburetor has been set at the factory to pro‐

vide an optimum fuel-air mixture under most

operating conditions.

9.1

Adjusting Idle Speed

0000-GXX-B008

► Start and warm up the engine.
9.1.1

Engine stops while idling

► Turn the idle speed screw (LA) clockwise until

the cutting blades begin to run – then back it

off about 1 full turn.

9.1.2

Cutting blades run when engine is

idling

► Turn the idle speed screw (LA) counterclock‐

wise until the cutting blades stop moving –

then turn it about another full turn in the same

direction.

WARNING

If the cutting blades continue to run while the

engine is idling, have your power tool checked

and repaired by your servicing dealer.

10 Spark Arresting Screen in

Muffler

WARNUNG

To reduce the risk of fire caused by hot particles

escaping from the machine, never operate the

machine without a spark arresting screen, or with

the spark arresting screen damaged. Do not

modify the muffler or spark arresting screen.

NOTICE

According to the law or regulations in some

countries or federal states, certain operations

may only be carried out if a properly serviced

spark arresting screen is provided.
► If the engine is down on power or maximum

speed is irregular, check the spark arresting

screen in the muffler

WARNING

Wait for the engine to cool down completely

before performing this work.

0008BA015 KN

► Use a 15 mm socket wrench to unscrew the

spark arresting screen

► Clean the dirty spark arresting screen, replace

if damaged or heavily carbonized

► Refit the spark arresting screen and tighten it

down firmly

English

8 Cleaning the Air Filter

0458-447-8321-D

Содержание HS 56

























Результаты поиска

Содержание HS 56

Отзывы:

Бренды по названию

Популярные бренды

Stihl HS 56, Инструкция по эксплуатации

Результаты поиска

Содержание HS 56

Отзывы:

Бренды по названию

Популярные бренды