Stihl FS 56 Скачать руководство пользователя страница 28

Страница: 28 / 44

FS 56, FS 56 R, FS 56 C, FS 56 RC

English

If there is a noticeable loss of engine

power

Move the choke lever (1) to

Turn the screw (2) in the filter

cover (3) counterclockwise until the

cover is loose.

Ease the filter cover (3) over the

choke lever and lift it away.

Clean away loose dirt from around

the filter.

Reach into the recess (4) in the filter

housing and take out the felt

filter (5).

Fit a new felt filter element (5). As a

temporary measure you can knock it

out on the palm of your hand or blow

it out with compressed air. Do not

wash.

NOTICE

Replace damaged parts.

Fit the felt filter (5) in the filter

housing, make sure it is properly

seated – the arrow points to the

recess.

Move the choke lever (1) to

Fit the filter cover in position,

making sure the screw is square.

Tighten down the screw.

The carburetor has been set at the

factory to provide an optimum fuel-air

mixture under most operating

conditions.

Adjusting Idle Speed

Engine stops while idling

Warm up the engine for about

3 minutes.

Turn the idle speed screw (LA)

slowly clockwise until the engine

runs smoothly – the cutting

attachment must not run.

Cutting attachment runs when engine is

idling

Turn the idle speed screw (LA)

counterclockwise until the cutting

attachment stops moving and then

rotate the screw another 1/2 to 3/4

turn in the same direction.

WARNING

If the cutting attachment continues to run

when the engine is idling, have your

machine checked and repaired by your

servicing dealer.

Cleaning the Air Filter

547BA022 KN

547BA023 KN

Adjusting the Carburetor

0815BA006 KN

Содержание FS 56













































Результаты поиска

Содержание FS 56

Отзывы:

Похожие инструкции для FS 56

Бренды по названию

Популярные бренды

Stihl FS 56, Инструкция по эксплуатации

Результаты поиска

Содержание FS 56

Отзывы:

Похожие инструкции для FS 56

Бренды по названию

Популярные бренды