Stihl FR 235 Скачать руководство пользователя

Страница: 19 / 24

► Push the flexible shaft (6) into the flexible drive

tube (2).

The end of the flexible shaft (6) that was previ‐

ously in the powerhead now points toward the

coupling sleeve (5).

0000-GXX-7846-A0

► Turn flexible shaft (6) back and forth and push

it in direction of coupling sleeve (5) until dis‐

tance ‘a’ is 1.5 cm.

► Fit the flexible drive tube (2) with the flexible

shaft (6) in the powerhead and align it so that

the word TOP on the flexible drive tube (2)

faces up.

► Fit the screw (1).

► Secure throttle cable (4) to flexible drive tube

(2) with the cable retainers (3), making sure

the throttle cable (4) is not wrapped around

the drive tube (2).

16.3

Lubricating the Gearbox

0000-GXX-3044-A0

► Remove the screw plug (2).

► If no grease can be seen on the end of the

screw plug (2):

► Screw the tube (1) of STIHL gear grease

into the filler hole.

► Squeeze 5 g of STIHL gear grease into the

gear housing.

► Unscrew the tube (1) of STIHL gear grease.

► Refit and tighten down the screw plug (2)

firmly.

► Run the trimmer for 1 minute.

STIHL gear grease is distributed evenly.

16.4

Adjusting the Throttle Cable

► Start the engine.

90°

0000-GXX-8178-A0

► Lay the flexible drive tube on the ground in a

90° curve.

0000-GXX-8179-A0

► Pull the trigger (1) without depressing the lock‐

out lever (2).

► If the engine accelerates: Hold the trigger (1)

depressed and turn screw (3) counterclock‐

wise until there is no further audible drop in

engine speed.

The throttle cable was over-tensioned.

► Pull the trigger (1) and hold it there without

depressing the lockout lever (2).

► Turn screw (3) clockwise until the engine

accelerates.

► Turn screw (3) back 2 turns counterclockwise.

The engine idles and the throttle cable adjust‐

ment is correct.

► Shut off the engine.

16.5

Sharpening and Balancing a

Metal Cutting Attachment

Correctly sharpening and balancing metal cutting

attachments requires a lot of practice.
STIHL recommends you have metal cutting

attachments resharpened and balanced by a

STIHL servicing dealer.

► Sharpen the metal cutting attachment as

described in the instructions and on the pack‐

aging supplied with the cutting attachment you

are using.

16 Maintenance

English

0458-527-0121-B

Содержание FR 235

























Результаты поиска

Содержание FR 235

Отзывы:

Похожие инструкции для FR 235

Бренды по названию

Популярные бренды

Stihl FR 235, Инструкция по эксплуатации

Результаты поиска

Содержание FR 235

Отзывы:

Похожие инструкции для FR 235

Бренды по названию

Популярные бренды