Stihl FR 131 T Скачать руководство пользователя

Страница: 35 / 44

FR 131 T

English

Repeat the above procedure as

necessary until both lines reach the

limiter blade on the deflector.
Rotating the spool from one stop to the

next advances about 4 cm (1 1/2 in) of

fresh line.

Replacing Nylon Line

STIHL PolyCut
Precut lengths of nylon line can be fitted

to the PolyCut in place of the cutting

blades.
STIHL DuroCut, STIHL PolyCut

WARNING

To reduce the risk of injury, always shut

off the engine before refilling the mowing

head.

Fit precut lengths of nylon line in the

mowing head as described in the

instructions supplied.

Replacing Cutting Blades

STIHL PolyCut
Always check the mowing head for signs

of wear before installing new cutting

blades.

WARNING

If there are signs of serious wear,

replace the complete mowing head.
The thermoplastic cutting blades are

referred to as "blades" in the following.

The mowing head is supplied with

illustrated instructions for replacing the

blades. Keep the instructions for the

mowing head in a safe place.

WARNING

To reduce the risk of injury, always shut

off the engine before installing the

blades.

Remove the mowing head.

Replace blades as shown in the

illustrated instructions.

Mount the mowing head on the

machine.

Maintenance Work

STIHL recommends that you have

servicing and repair work carried out

exclusively by an authorized STIHL

servicing dealer.

Anti-Vibration Elements

Four anti-vibration springs are installed

between the powerhead and support

frame. Have them checked if there are

signs of wear or a noticeable increase in

vibration levels.

Inspections and Maintenance

by Dealer

0000-GXX-1310-A0

Содержание FR 131 T













































Результаты поиска

Содержание FR 131 T

Отзывы:

Похожие инструкции для FR 131 T

Бренды по названию

Популярные бренды

Stihl FR 131 T, Инструкция по эксплуатации

Результаты поиска

Содержание FR 131 T

Отзывы:

Похожие инструкции для FR 131 T

Бренды по названию

Популярные бренды