Stihl FR 131 T Скачать руководство пользователя

Страница: 32 / 44

FR 131 T

English

If engine running behavior is

unsatisfactory even though the air filter

is clean and the carburetor is properly

adjusted, the cause may be the muffler.
Have the muffler checked for

contamination (carbonization) by your

servicing dealer.
STIHL recommends that you have

servicing and repair work carried out

exclusively by an authorized STIHL

servicing dealer.

Check grease level after every 25 hours

of operation and re-lubricate if

necessary.

Remove the screw plug (1).

If no grease can be seen on the

inside of the screw plug (1): Screw

the tube (2) of STIHL gear lubricant

(special accessory) into the filler

hole.

Squeeze no more than 5 g (1/5 oz)

grease into the gearbox.

NOTICE

Do not completely fill the gearbox with

grease.

Unscrew the tube (2).

Insert the screw plug (1) and tighten

it down firmly.

Check the film of grease regularly –

about every 25 hours of operation.

Unscrew the screw (1) and remove

it with the washer (2).

Pull out the flexible shaft (3).

Pull the flexible shaft (2) out of the

protective tube (3).

Mark the installed position of the

flexible tube.

Coat the shaft uniformly with STIHL

multipurpose grease (special

accessory). Do not apply too much

grease.

NOTICE

If the drive shaft has turned blue, install

a new one.

Engine Running Behavior

Lubricating the Gearbox

0000-GXX-0536-A0

Lubricating the Flexible Shaft

0000-GXX-1309-A0

0812BA036 KN

Содержание FR 131 T













































Результаты поиска

Содержание FR 131 T

Отзывы:

Похожие инструкции для FR 131 T

Бренды по названию

Популярные бренды

Stihl FR 131 T, Инструкция по эксплуатации

Результаты поиска

Содержание FR 131 T

Отзывы:

Похожие инструкции для FR 131 T

Бренды по названию

Популярные бренды