background image

:DUUDQW\3HULRG

The warranty periods will begin on the
date the utility equipment engine is 
purchased by the initial purchaser and
you have signed and sent back the 
warranty card to STIHL. If any emission
related part on your engine is defective,
the part will be replaced by STIHL 
Incorporated at no cost to the owner.
Any warranted part which is not 
scheduled for replacement as required
maintenance, or which is scheduled only
for regular inspection to the effect of 
"repair or replace as necessary" will be
warranted for the warranty period. 
Any warranted part which is scheduled
for replacement as required mainten-
ance will be warranted for the period of
time up to the first scheduled replace-
ment point for that part.

'LDJQRVLV

You, as the owner, shall not be charged
for diagnostic labor which leads to the
determination that a warranted part is 
defective. However, if you claim warranty
for a component and the machine is 
tested as non-defective, STIHL 
Incorporated will charge you for the cost
of the emission test.
Mechanical diagnostic work will be 
performed at an authorized STIHL 
servicing dealer. Emission test may be
performed either at STIHL Incorporated
or at any independent test laboratory. 

:DUUDQW\:RUN

STIHL Incorporated shall remedy 
war-ranty defects at any authorized
STIHL servicing dealer or warranty 
station. Any such work shall be free of
charge to the owner if it is determined
that a warranted part is defective. Any
manufacturer-approved or equivalent
replacement part may be used for any
warranty mainten-ance or repairs on
emission-related parts and must be 
provided without charge to the owner.
STIHL Incorporated is liable for damages
to other engine components caused by
the failure of a warranted part still under
warranty.

The California Air Resources Board’s
Emission Warranty Parts List specifically
defines the emission-related warranted
parts. These warranted parts are:

Carburetor
Choke (Cold start enrichment system)
Intake manifold
Air filter 
Spark plug
Magneto or electronic ignition system
(ignition module)
Catalytic converter (if applicable)
Fasteners

:KHUHWRPDNHDFODLPIRU:DUUDQW\

6HUYLFH

Bring the product to any authorized
STIHL servicing dealer and present the
signed warranty card. 

0DLQWHQDQFH5HTXLUHPHQWV

The maintenance instructions in this 
manual are based on the application of
the recommended 2-stroke fuel-oil 
mixture (see also instruction "Fuel"). 
Deviations from this recommendation 
regarding quality and mixing ratio of fuel
and oil may require shorter maintenance
intervals.

/LPLWDWLRQV

This Emission Control Systems 
Warranty shall not cover any of the 
following:

- repair or replacement required 

because of misuse, neglect or lack of
required maintenance, 

- repairs improperly performed or 

replacements not conforming to
STIHL Incorporated specifications that
adversely affect performance and/or
durability, and alterations or 
modifications not recommended or 
approved in writing by STIHL 
Incorporated, 

and 

- replacement of parts and other 

services and adjustments necessary
for required maintenance at and after
the first scheduled replacement point.

%5

Содержание BR 320































Отзывы: