![background image](http://html.mh-extra.com/html/stihl/6290/6290_instruction-manual_1379223037.webp)
35
DE
FR
NL
IT
ES
PT
NO
SV
FI
DA
PL
SL
SK
HU
EN
0478 670 9906 A - EN
●
The scarifier must only be operated by
one person. Other persons must keep
out of the danger area. (
8.3 Correct motor load
Only switch on the motor when the
scarifying unit is in the transport position.
The scarifier load must never cause the
motor speed to drop significantly.
If the speed drops, reduce the feed speed.
If necessary, place the scarifying unit in
the transport position and select a
shallower cutting depth before continuing
with scarifying.
8.4 Thermal motor overload protection
If an overload of the motor occurs during
operation, the built-in thermal overload
protection device automatically switches
off the motor.
Causes for an overload:
– Excessive rate of feed
– Blades cut too deeply into the ground
– Unsuitable or excessively long electric
– Inadequate cleaning of the cooling air
guide (inlet slots)
Recommencing operation
Resume normal operation of the machine
following a cooling period of up to 10 min
(depending on the ambient temperature).
(
8.5 If the scarifying unit becomes
blocked
Switch off the motor immediately and
disconnect the mains plug. Then inspect
the machine, in particular the scarifying
unit, for damage and eliminate the cause
of the fault.
The machine is equipped with several
safety devices for safe operation and for
the prevention of improper use.
9.
1
Safety devices
The scarifier is equipped with safety
devices which prevent inadvertent contact
with the blades and with ejected scarified
material.
These include the housing, discharge flap
and correctly installed handlebar.
9.2 Two-hand operation
The motor can only be switched on by
pressing and holding the ON button with
the right hand and then pulling the
motorstop lever to the handlebar with the
left hand.
1
0.
1
Electrical connection
Only cables which are no lighter than the
following rubber sheathed cables may be
used as electric cables:
H07 RN-F DIN/VDE 0282
Minimum cross-section:
up to 25 m length: 3 x
1
,5 mm²
up to 50 m length: 3 x 2,5 mm²
The connectors of the electric cables must
be made of rubber or have a rubber cover
and conform to the following standard:
DIN/VDE 0620
The mains voltage and mains frequency
must correspond to the information on the
rating plate and the information contained
in the section "Technical specifications"
(
The power cable must be adequately
protected by fuse (
This machine is intended for operation with
a power supply having a system
impedance of Z
max
at the transfer point
(house connection) of maximum
0,49 ohms
(at 50 Hz).
9. Safety devices
Risk of injury!
If a safety device is found to be
defective, the machine must not be
operated. Consult a specialist
dealer; STIHL recommends STIHL
specialist dealers.
1
0. Operating the machine
Danger of electric shock!
Observe the safety instructions in
the section "For your safety"
(
If using a cable drum, the
connection cord must be unwound
completely, otherwise electrical
resistance may cause loss of power
and overheating.
Содержание 6290
