Stiga ROYAL LINE 1171 HST, Инструкция по эксплуатации, Страница: 9 / 18

60
ENGLISH
EN
• Never drive across a slope. Move from the top down, and
from the bottom to the top. Be careful when changing
direction on a slope. Avoid steep slopes.
• Never operate the machine with insufficient protection or
without the safety devices in place.
• Existing safety devices must not be disconnected or
disengaged.
• Do not alter the engine’s regulator setting and do not race
the engine. The possibility of personal injury increases
when the engine is run at high revs.
• Never use the snow thrower near enclosures, cars,
windowpanes, slopes etc. without properly setting the
discharge chute deflector.
• Always keep children away from areas to be cleared. Get
another adult to keep the children under supervision.
• Do not overload the machine by driving it too fast.
• Take care when reversing. Look behind you before and
during reversing to check for any obstacles.
• Never point the discharge chute towards bystanders. Do
not allow anyone to stand in front of the machine.
• Disengage the auger when the snow thrower is to be
transported or is not in use Do not drive too fast on
slippery surfaces when transporting.
• Only use accessories that are approved by the machine’s
manufacturer.
• Never drive the snow thrower in bad visibility or without
satisfactory lighting.
• Always ensure you have a good balance and a tight grip
on the handle.
• Never use the snow thrower on a roof.
• Do not touch engine components because they are warm
during use. Risk of burn injuries.
2.4 MAINTENANCE AND STORAGE
• Tighten all nuts and screws so that the machine is in safe
working condition. Check the shear bolts regularly.
• Always use genuine spare parts. Non-genuine spare parts
can entail a risk of injury, even if they fit the machine.
• Never store the machine with petrol in the tank in
buildings where the fumes can come into contact with
open flames or sparks.
• Allow the engine to cool before putting the machine in
store.
• Before a long storage, check the instructions for
recommendations.
• Replace damaged warning and instruction stickers.
• Let the engine run a couple of minutes with the auger
connected after use. This prevents the auger from
freezing solid.
3 ASSEMBLY
Note: Instructions to the left and right sides start from the
driving position behind the snow thrower.
3.1 CONTENTS - OUTER PACKING
The packing contains:
- One snow thrower
- One adjustment lever
- One gear rod
- One discharge chute
- One set of instructions
- One assembly kit
3.2 UNPACKING
1. Remove all loose items from the carton.
2. Cut the four corners of the carton and let the sides fall
down.
3. Cut off the plastic straps.
4. Unscrew the screws (B) that fasten the shoes to the
bedding. See fig. 1.
5. Cut the plastic tape holding the control wires on the
underside of the handle.
3.3 HANDLE, SEE FIG. 2
1. Loosen, but do not remove, the securing nuts in the upper
holes.
2. Fold up the upper part of the handle. NOTE! Make sure
the control wires do not jam.
3. Fit screws from the outside in the lower holes and
assemble with the following parts:
A Screws
D Lock nut
4. Tighten the four nuts.
3.4 SNOW DISCHARGE CHUTE, SEE FIG. 3
1. Place the discharge chute (E) on the flange against the
worm gear.
2. Mount the carriage piece (F) with two screws
3. Adjust the
chute worm gear
. See 6.6.4.
4. Tighten the chute worm gear properly.
3.5 ADJUSTMENT LEVER, SEE FIG. 4
1. Place the shaft through its hole in the control panel and
into the angle joint.
3. Lock the joint with the locking pin (G).
4. Check the discharge chute by turning it fully in both
directions. The chute should rotate freely.
3.6 CONTROL KNOBS, FIG. 5
The assembly is performed as follows:
1. Screw the nut (J) onto the lever.
2. Mount the control knob (K) onto the lever.
3. Tighten the nut on the underside of the control knob.