Stiga MP2 500 Li D48 Series Скачать руководство пользователя страница 30

EN - 13

5. 

The danger LED lights up 

on the display (Fig.24.A).

The thermal protection has tripped 

due to overheating of the machine.

Wait for at least 5 minutes and restart the 

machine.

6. 

The cut grass is no 

longer collected in 

the grass catcher.

The cutting means hit a foreign object.

Immediately turn off the motor 

and remove the safety key.

Check if there is any damage and 

contact a Service centre to replace the 

cutting means if necessary (par. 8.1).

The inner part of the chassis is soiled.

Clean the inner part of the chassis to 

facilitate the evacuation of the grass 

toward the grass catcher (par. 7.3.2).

7. 

Mowing is difficult.

The cutting means is not in good state.

Contact the Authorised Service 

Centre for the sharpening or 

replacement of the cutting means.

8. 

Excessive noise and/

or vibration is experi

-

enced whilst working.

Cutting means fittings are loose or 

the cutting means is damaged.

Immediately turn off the motor 

and remove the safety key.

Contact the Authorised Service Centre for 

checks, replacements or repairs (par. 8.1).

9. 

Battery power re

-

serve is low.

Severe working conditions requiring 

greater current absorption.

Optimise operations (par. 7.2.1).

Battery is insufficient for 

operating requirements.

Use additional batteries or batteries with 

extended power reserve (par. 15.2).

10. 

The battery charger is 

not charging the battery.

Battery is not correctly inserted 

in the battery charger.

Check it is correctly inserted (par. 7.2.3).

Unsuitable environmental conditions.

Recharge the battery in places with 

suitable temperatures (see battery/

battery charger instruction manual).

Dirty contacts.

Clean the contacts.

The battery charger is not energised.

Check it is plugged in and the 

power socket is energised.

Faulty battery charger.

Replace with an original spare part.
If the problem persists, refer to the 

battery/battery charger manual.

15.  OPTIONAL ATTACHMENTS

 15.1  "MULCHING" KIT

Finely chops the cut grass and leaves it on the 

lawn, instead of collecting it in the grass catcher 

(for machines equipped with it) (Fig.25).

 15.2  BATTERIES

Different capacity batteries are available to suit 

specific operating requirements (Fig.26). The 

list of approved batteries for this machine can 

be found in the "Technical Data" table.

 15.3  BATTERY CHARGER

Device used to recharge the battery (Fig.27).

Содержание MP2 500 Li D48 Series



































Отзывы: