manualshive.com logo in svg

Stiga 2021 Edition PARK 320 P, Руководство по ремонту

Поделиться
Скачать
Stiga 2021 Edition PARK 320 P Скачать руководство пользователя страница 119

WORKSHOP MANUAL

PARK

Chapter

9 - ELECTRICAL SYSTEM 

EDITION

2020

PAGE

119 /

124

 

Problem

Probable cause

Solution

2) Symptom: The brake does not start.

Worn armature / brake poles

• End of the clutch life

• Replace the clutch

Contaminated friction surfaces

• Oil seeping on the brake

• Check and repair leaks
• Replace the clutch

3) Symptom: Clutch slippage.

Low supply voltage (less than 12 VDC 

to the clutch)

• Faulty battery

• Replace the battery

• Faulty charging system

• Repair or replace.

•  Faulty wiring or connections of the 

PTO switch

•  Check, repair or replace

Inadequate power supply

• Clutch cables broken

• Repair or replace.

• Faulty electrical system

•  Measure the clutch coil resist-

ance and the voltage supply. If 

both are correct, the electrical 

system is defective. Repair or 

replace.

Overloaded clutch

•  Clogged cutting deck

•  Remove the excess grass

•   Deformed shafts. etc.

• Replace

Contaminated friction surfaces

• Oil seeping on the brake

• Check and repair leaks
• Replace the clutch

4) Symptom: Clutch noise and vibrations.

The plate hits against the anti-rotational 

bracket

• A little bit of noise is normal

•  If the noise is excessive, repair 

or replace the anti-rotational 

device.

Loose clutch on the motor shaft

•  Loose assembly (screw not prop-

erly tightened) 

•  Tighten the mounting screw 

according to the specifications 

(60-70Nm)

•  Fastening screw is too long and 

does not allow to axially lock the 

clutch

•  Use an original replacement 

screw

•  The mounting washers are too thin 

and deformed after tightening the 

screw

•  Use original spare parts

Broken spring

•  Loose fitting

• Replace the clutch

9.3.13  Checking the function of the electromagnetic clutch

The electromagnetic clutch is used to connect or 

disconnect, via a switch, the equipment used on 

the machine. In addition, the clutch is designed 

to activate a brake on the output shaft, when it is 

disengaged.  
•   The field coil is mounted to a bearing support 

and does not rotate. 

•   The rotor is attached to the power output shaft 

and rotates around the field assembly. 

•  The assembly is connected to the output pulley.

•   The  armature  unit  is  assembled  close  to  the 

brake unit rotor.

Содержание 2021 Edition PARK 320 P





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды