StewMac Monarch Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 14

background image

stewmac.com

©2018 StewMac

page 14 of 14

Here’s how the controls work:

Treble:

Boosts the highs.

Bass:

Boosts the lows.

Gain:

Adjusts the amount of drive.

Level:

Adjusts the output level, unity is around 9 o’clock…

This thing is LOUD!

Power:

Use a standard 9 volt DC power supply with a

2.1mm negative-center barrel (not included). We always
recommend pedal-specific, transformer-isolated wall-wart
power supplies or supplies with separate isolated outputs.
Pedals will make extra noise if there is ripple or unclean
power. Switching-type power supplies, daisy chains and
non-pedal specific power supplies do not filter dirty power as
well and let through unwanted noise.

Do not run at higher

voltages!

Current draw is 3 mA.

INPUT

OUTPUT

9V DC

BASS

TREBLE

LEVEL

GAIN

BYPASS

«
...
12
13
14

Содержание Monarch















Отзывы:

Нет отзывов

Похожие инструкции для Monarch

System X S/H Noise

Бренд: Frequency Central Страницы: 4

Бренд: Pyramid Страницы: 32

Бренд: Boss Страницы: 22

SUPER PHASE SHIFTER SP400

Бренд: Behringer Страницы: 2

Бренд: twisted electrons Страницы: 16

Guitar Rig Kontrol

Бренд: Native Instruments Страницы: 49

Бренд: SAL Страницы: 16

Бренд: Corsynth Страницы: 8

Бренд: Fostex Страницы: 19

Бренд: Solid State Logic Страницы: 180

NEXUS-IP-G1-US-IOT

Бренд: Telex Страницы: 18

Бренд: FuzzDog Страницы: 5

QuarterHorse DH25H

Бренд: YORKVILLE Страницы: 9

Бренд: YORKVILLE Страницы: 22

Бренд: YORKVILLE Страницы: 36

POWER MAX YS1011

Бренд: YORKVILLE Страницы: 40

Бренд: YORKVILLE Страницы: 36

Бренд: Stryker Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды