StewMac Monarch Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 14

background image

stewmac.com

©2018 StewMac

page 9 of 14

Step 7: Install four control pots

The last components to go onto the circuit board are the four
control pots. They install on the

back of the board

. Each pot

has three connecting lugs, refer to the below left graphic to
be sure your orientation is correct when installing the pots.

If any pot has an index pin protruding from the case, break
it off before installation, so the pot will mount flush against
the pedal case. Needle nose pliers work well for removing
the pins.

Use the

adhesive foam tape

to insulate the back of the

pots from the soldered leads of the other parts on the circuit
board. Solder the pot in place, making sure the foam back
sits at the back of the board.

Refer to the left graphic to be sure your orientation is correct
when installing the pots.

B100K

A1M

A1M

A1M

A1MΩ “treble” pot

#7459

Apply adhesive foam tape to back of the pots

If the pot has an index pin, break it off.

A1MΩ “bass” pot

#7459

A1MΩ “gain” pot

#7459

Apply adhesive foam tape to back of the pots

B100KΩ “level” pot

#7453

«
...
7
8
9
10
11
...
»

Содержание Monarch















Отзывы:

Нет отзывов

Похожие инструкции для Monarch

Бренд: Marenius Страницы: 11

Бренд: Truetone Страницы: 2

Flanger LEF-312

Бренд: FAME Страницы: 15

DITTO JAM X2 LOOPER

Бренд: TC Electronic Страницы: 7

Бренд: Meicheng Страницы: 28

Бренд: Gemini Страницы: 13

TEAC PROFESSIONAL M-164

Бренд: Tascam Страницы: 40

Бренд: Gemini Страницы: 28

Бренд: Sonocurrent Страницы: 3

NetWave PRE99-1600D-08

Бренд: Harris Broadcast Страницы: 112

PEMUTT Mutterstolz

Бренд: Palmer Страницы: 60

Бренд: Calrec Страницы: 198

Бренд: XTE Electronic Страницы: 11

Бренд: Veeder-Root Страницы: 16

HQ Power Lite Puter LPTC401

Бренд: Velleman Страницы: 10

Бренд: Velleman Страницы: 11

Бренд: Velleman Страницы: 13

Бренд: Velleman Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды