manualshive.com logo in svg

Stewart MacDonald 5297, Инструкция по сборке, Страница: 36 / 42

Поделиться
Скачать
Stewart MacDonald 5297 Скачать руководство пользователя страница 36

stewmac.com

diameters of the strings . Clean the saw marks with a needle 
file, and file a slight “ramp” at the upper edge of each bridge 
pin hole to soften the angle of the string . 

Apply Titebond to the bridge, and reclamp the bridge in 
place on the soundboard . Use at least three deep-throat 
clamps with your exterior and interior bridge cauls (pic-
tured) . Clean up the squeezed-out glue with a damp cloth, 
and allow at least 24 hours drying time . 

Installing the bridge 

When the glue has dried, remove the center clamp to expose 
the bridge pin holes, leaving the outer clamps to hold the 
interior bridge caul in place . The caul will act as a backing 
block to prevent wood from splitting out as you drill . 

Drill the holes through the soundboard, and into the caul, 
with a 3/16" drill bit (pictured) . We recommend using a 
bridge pin reamer for tapering the holes to fit the supplied 
bridge pins . 

Use a section of coping saw blade or jig saw blade, with the 
teeth cutting on the upstroke to avoid tear-out, to form slight 
notches in the bridge, soundboard and bridge plate . These 
slots will accommodate the strings, and should be no deeper 
than 1/3 to 1/2 the diameter of the string, just enough so the 
strings don’t pop out (the remainder of each string will fit 
in the bridge pin groove) . The slot widths should match the 

Fitting the bridge pins

Trim the length: Mark the center of the saddle . From the 
centerline, measure and mark 1-1/2" out from each side . 
Equally from each end, saw off excess to make a 3" wide 
saddle (slightly larger than the slot) . Using the same sanding 
method to thin the saddle (above), sand equally on each end 
to reduce the saddle length, test fitting often . You’ll feel the 
saddle “click” into the slot when it reaches the bottom . The 
taller side of the saddle radius is for the bass strings .

You'll adjust the bridge height later during setup .

The slot in the bridge is 2-29/32" in length and 3/32" wide . 
The saddle must be thinned and ends trimmed to fit .

Thickness sand: Attach two pieces of sandpaper, 100-grit 
and 220-grit, to a hard flat surface with double-stick tape . 
Sand the flat sides of the saddle blank back and forth on 
the papers . Check the thickness frequently by attempting 
to slide the saddle into the slot . Work slowly and test often . 
You can remove a little more, but once you've gone to far, 
it's impossible to add it back on!

Fitting the bridge saddle 

34

Содержание 5297











































Отзывы:

Нет отзывов