manualshive.com logo in svg

Stewart MacDonald 5297, Инструкция по сборке, Страница: 23 / 42

Поделиться
Скачать
Stewart MacDonald 5297 Скачать руководство пользователя страница 23

stewmac.com

Clamp the fretboard to a board, rest that board on its side, 
and clamp this assembly to your benchtop with the bass 
side of the fretboard facing up . Measure midway between 
the appropriate fret slots, center carefully on the fretboard 
edge, and lightly centerpunch for the side dot position 
marker holes . Two evenly-spaced dots will be installed at the 

12th fret . Drill all these holes with a 1/16" bit . One at a time, 
touch a drop of medium-viscosity super glue to each hole 
and insert the end of the plastic side dot rod . Snip it close to 
flush . Level the dots with a smooth mill file (or the 120-grit 
edge of the carpenter’s level used earlier) . Use a light touch 
in sanding so you don't alter the fretboard edge .

Installing the fretboard side dots 

With a flat block (or a 16" radius block if available), stroke 
the fretboard lengthwise a few times, uniformly with 220-
grit sandpaper, as a final smoothing to prepare for fretting . 

Do your fretting on a flat hard surface (we used a slab of 1- 
1/4" thick marble) . The fretwire is curved, and must be cut 
to length for each fret slot, but leave 1/8" overhang on each 
side . Keep the cut frets arranged in order . 

KIT TIP: Gluing the frets 

There’s no need to use glue on a new fretboard, but 
the choice is yours . Glue keeps the frets tight and lu-
bricates the slot for possibly easier fret installation, 
but also may produce an occasional loose fret end . 

Set the first fret in place and hold it so that it can’t tip, to 
prevent wood chipping (pictured) . Seat the two fret ends 
with one sharp hammer blow each, then hammer back and 
forth across the fret . Since the fretwire is more curved than 
the fretboard, the fret straightens as it’s hammered in . This 
causes the barbs on the fret tang to move sideways in the 
slot, tightening the fit . Avoid tipping the hammer face so that 
its edge hits the fret, or you’ll dent the wire . Hammer from 
your wrist, in short crisp blows (pictured) . A scrap piece of 
fretboard has been included with your kit, as well as enough 
fretwire to practice fretting . Measure out the frets you will 
actually use on your fretboard, then use the leftover fretwire 
to test your skills on the scrap . 

As you progress down the fretboard, the compression of 
the fret tangs will cause the fretboard to backbow a little, 
so be sure to hold the fretboard flat as you hammer . Install 
the wire up to the 12th fret and stop . The remaining frets, in 
the fretboard extension over the body, will be installed later, 
after the neck is “dry-fitted” to the body . We do this because 
the fretboard extension will curve slightly from fret compres-
sion, making sighting and fitting the neck more difficult . 

Test the tightness of a couple of fret ends by prying up a little 
with your fingernail . The fret ends should be seated tightly 
(pictured) . To ensure this, you can rest the fretboard on 
edge and run a bead of water-thin super glue into the slot . 
Let it run through the slot and out the other side . Loose frets 
can be clamped using a 16"-radius sanding block as a caul 

Installing the frets 

21

Содержание 5297











































Отзывы:

Нет отзывов