manualshive.com logo in svg

Stewart MacDonald 5297, Инструкция по сборке, Страница: 28 / 42

Поделиться
Скачать
Stewart MacDonald 5297 Скачать руководство пользователя страница 28

stewmac.com

Removing wood from the top

edge tips the neck upward

Removing wood at the bottom

edge tips the neck back

the side . To check the angle, lay a straightedge on the frets 
so that it extends to the bridge . Ideally, it will just graze the 
top of the bridge (without a saddle) . If it falls above or below 
the top of the bridge by more than 1/32", an adjustment is 
needed at the heel . 

The most common adjustment is removing wood from the 
bottom of the heel cheeks . Removing wood from the bottom 
of the heel on both the treble and bass sides equally will tip 
the neck back (illustrated) . Remove the wood in a wedge 
shape which tapers to zero at the top edge of the cheeks . 

Use the formula in “Understanding neck angle geometry” to 
determine how much wood to remove . With a sharp pencil 
and a straightedge, mark the area to be chiseled away in a 
straight line from the bottom of the heel to the zero point 
at the top . Continue this line across the heel cap and up the 
opposite side . These lines may be tricky to draw, because 
they must taper away to nothing — to the zero point at the 
top of the heel . 

With a sharp chisel, remove about half of the measured 
amount of wood . Don’t overdo it: set the neck into the body 
and check the fit . You’ll finish the shaping with sandpaper — 
preferably 100-grit emery cloth (cloth-backed sandpaper) . 
Loosen the neck joint and slide a strip of this sandpaper or 
emery cloth between the heel cheek and the body with the 
abrasive side facing the cheek . Slide the strip almost — but 
not quite — to the top edge of the heel (this top edge should 
be left intact) . Be sure to angle down to keep the heel cap in 
contact with the sides . Hold the heel against the guitar body 
and pull the strip out toward you (pictured) . This removes 
a little bit of wood while conforming to the shape of the 
guitar body . Shake the sawdust off the sanding strip and 
repeat the procedure on the opposite cheek . Sand equally 

Neck adjustment: tilt the neck back 

The first area that may need to have a small amount of 
wood removed is the treble or bass cheek . Wood removed 
here controls the “side-to-side” alignment of the neck to 
the centerline . If the neck is misaligned side-to-side, one 
of the outside E-strings will be too close to the edge of the 
fretboard . A tiny amount of wood is all it takes to make an 
adjustment here . Remove this bit of wood uniformly across 
the contact area on one cheek to tip the neck in the proper 
direction (this won’t change the neck angle when viewed 
from the side of the body) . Use a straightedge laid against 
both the treble and bass sides of the fretboard to check the 
alignment: it should extend out the same distance from 
center on either side at the bridge (pictured) . 

You may not need to make an adjustment at this stage . If 
the neck is off-center by only 1/32" or less, don’t try to cor-
rect it . Remember that a tiny bit of wood removal makes a 
big difference in the neck’s relationship to the centerline! 

The top edge of the cheeks is the pivot point between the 
neck and body . This controls the neck angle as viewed from 

Neck adjustment: side-to-side 

26

Содержание 5297











































Отзывы:

Нет отзывов