background image

LIGHTING INSTRUCTIONS 

 

 
 
WARNING: IMPORTANT! 
 
 
 
 
 
 
 

                      

20 

 

 

 
 
 
 
 

 
 
 

BEFORE LIGHTING… 

 

Inspect the gas supply hose prior to turning the gas 
“ON”. If there is evidence of cuts, wear, or abrasion, 
it must be replaced prior to use. Do not use the grill 
if the odor of gas is present. Only the pressure 
regulator and hose assembly supplied with the unit 
should be used. Never substitute regulators for 
those supplied with the grill. If a replacement is 
necessary, contact the factory for proper 
replacement. 
 
Screw the regulator (type QCC1) onto the tank. 
Leaks check the hose and regulator connections 
with a soap and water solution before operating the 
grill (see assembly instruction page 11). 
 

TO LIGHT THE GRILL BURNER: 
 

Make sure all knobs are “OFF” then turn on the gas 
supply from the LP tank. Always keep your face and 
body as far from the grill as possible when lighting. 
 
 

 
Your grill has an exclusive patented built-in ignition. 
The igniter is built in to the valve. To ignite each 
burner simply push and turn the control knobs to 
the HI setting, you will hear the valve click as it  

WARNING 

Failure to open grill lid during the lighting 
procedure could result in a fire or explosion 
that could cause serious bodily injury, death, 
or property damage. 

sends a spark to the pilot flame. If the burner does 
not light, wait 5 minutes for any excess gas to 
dissipate and then retry. 

 
Flame Characteristics: 
 

WARNING 

Never

 lean over the grill cooking area while 

lighting your gas grill. Keep your face and 
body a safe distance (at least 18 inches) from 
the cooking grid surface when lighting your 
grill by match. 

Check for proper burner flame characteristics. Each 
burner is adjusted prior to shipment; however, 
variations in the local gas supply may take minor 
adjustments necessary. 
 
Burner flames should be blue and stable with no 
yellow tips, excessive noise, or lifting. If any of 
these conditions exist call our customer service line. 
If the flame is yellow, it indicates insufficient air. If 
the flame is noisy and tends to lift away from the 
burner, it indicates too much air. 
 

TO MATCH LIGHT THE GRILL: 
 

If the burner will not light after several attempts then 
the burner can be match lit.  
 
If you’ve just attempted to light the burner with the 
igniter, allow 5 minutes for any accumulated gas to 
dissipate. Keep your face and hands as far away 
from the grill as possible. Insert a lit extended 
match or lighter through the cooking grids to the 
burner. Press the control knob and rotate left to the 
HI setting, continue to press the knob until the 
burner ignites. Burner should light immediately. If 
the burner does not light in 4 seconds turn the knob 
off, wait 5 minutes and try again. 
 
Keep a spray bottle of soapy water near the gas 
supply valve and check the connections before 
each use.

 

Содержание 720-0322

































Отзывы: