8
9
SLIDE MOUNT - (BAG B.3)
The Sterisil
®
System G5 will come with the slides affixed in the
correct direction for proper maintenance. Please consider the
orientation of the slides and affixing the slide mount to the wall
mounting plate before you start.
Affixing the Slide Mount to the Wall
• Mark the holes on the slide mounting plate.
• Screw the mounting plate to the wall and ensure it is level.
Securing the G5 to the Slide Mount
• Take the system and line up the rails on the back of the waffle
plate to the slides on the mounting plate. Slide the unit until
you hear the rails snap into place.
• Verify it is level.
ARTICULATING MOUNT - (BAG B.2)
Affixing the Articulating Mount to the Wall
• Use articulating mount hardware (included in package).
• Place the mount against the wall with the “up” arrow facing
the ceiling. Ensure the mount is level and mark your holes.
• Pilot holes are either 3/8” or 9/64”.
• Affix the mount to the wall with the appropriate combination
of hardware for your mounting surface.
• Confirm it is level.
Securing the G5 to the Articulating Mount
• The system will come with the waffle plate attached. Tack
the X-plate to the back of the waffle plate. You may need to
place the unit on the front face to accomplish this. Please
be mindful of the touchscreen if you do so. Use the packing
foam to avoid damage to the touchscreen.
• Mount the X-plate to the waffle plate using the bolts and
washers. Make sure the “up” arrow is facing the top of the
system.
• You will notice a notch in the upper middle portion of the
X-plate. Tighten a screw nut to this notch.
• Mount the system to the articulating mount by hanging the
top screw nut affixed to the X-plate in the notch on the arm
mount.
• Fasten the entire assembly to the wall mount with the two
remaining nuts. Be sure the unit is level and tighten with 1/2”
wrench.
• Properly orient the unit and tighten the forward tilt nuts once
system is completely level.
PERIPHERAL COMPONENTS
Peripheral components – No more than 50 feet from the system.
Depending on the customer’s specific configuration you may have optional components such as the Pre-filter
Kit and Booster Pump plumbed between the municipal source and the red “SOURCE” port on the system.
G5 POWER ADAPTER
• Select location within 6 feet of the outlet. Ensure there is no tension on the cable.
• If you choose to mount the power adapter on the wall, use hardware straps provided.
WATER STORAGE TANKS - (BAG C)
Storage tank sizes may differ with customer specifications and needs. Note: tank sizes will vary depending on
Stage 5 selection or pre-install requirements. As a default, the RO tank will be the larger of the two. Storage
tanks must be mounted within 50 feet of the system to maintain optimal water pressure. Set storage tanks in
desired locations. A common location is under a sterilization center sink.
• Wrap the threads with Teflon tape (included) on each bladder tank. Install the 3/8” valve and hand tighten it to
the larger RO tank. Do not over tighten this valve.
• Repeat this process with the 1/4” valve for the Dental Water Tank.
• Ensure the pressure of the tanks is between 8–10 psi Schrader valved pressure gauge.
FAUCET(S) INSTALLATION
The bottle fill configuration includes a white Autoclave Faucet and a chrome Dental Water Faucet. Dental water
is always plumbed to the chrome faucet. Typical mounting location is on a counter-top extended over a sink.
Direct feed systems only use the white Autoclave Faucet. Dental water is fed directly to the dental unit hand
pieces.
COUNTER-TOP MOUNT
Faucet assembly instructions are located on the back of the faucet box.
• Do not use the compression fittings provided. Instead use the provided push-fit connect.
• Drill 5/8” hole at the desired location.
• Place the faucet through the hole and mount using the hardware (included).
• Wrap the thread with thread tape prior to install.
• Place the under-sink mounting washer, and install the nut (included in box) and hand tighten.
Washer
Lock Washer
Quick Connect
Fitting
Plastic Gasket
Nut
Slide mount
Notch
Articulating mount
X-plate
