background image

CAUTION 1:

TURN ALL POWER OFF. NEVER EXPOSE EYES OR SKIN TO UVC LIGHT FROM ANY SOURCE - WEAR GLOVES,

FACE SHIELD AND COVER ALL EXPOSED SKIN. DO NOT TOUCH EMITTER™ GLASS WITHOUT GLOVES.

CAUTION 2:

INSTALL EMITTER TUBE BEFORE APPLYING POWER. FAILURE TO DO SO WILL TRIGGER THE "END-OF-LAMP-

LIFE CIRCUIT" AND THE EMITTER WILL FAIL TO LIGHT! IF THIS HAPPENS SHUT OFF POWER FOR 10 MINUTES, REINSTALL
/ INSTALL EMITTER AND TURN POWER BACK ON. EMITTER WILL LIGHT.

NOTE: Read this entire instruction sheet before starting the installation.

Made in USA

p

WARNING

!

Before installing fixture or performing maintenance or service on
fixture, turn off main power switch to unit. Electrical shock can cause
injury or death. There may be more than one disconnect switch.

p

CAUTION

!

Never expose eyes or skin to ultraviolet light from any source. After
installation, provide an interlock to turn off germicidal lamps when
access door is opened. Lamp must be off before entering HVAC unit
to perform maintenance or service. Personal injury may result.

p

CAUTION

!

Do not touch lamp glass without gloves. Damage to Emitter™ may
result. Oil from fingerprints will permanently etch glass of lamp and
weaken structure. Clean lamp after handling.

p

CAUTION

!

Lamp contains a small quantity of mercury. If a lamp breaks, clean
and dispose of with care.

p

CAUTION

!

Use only specified high-output, low temperature lamps with this
accessory. Use of a lower wattage or incorrect Lamp can result in
damage to accessory or lamp.

Safety Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0
Operation & Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0
Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0
Spare or Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0

1.0   SAFETY CONSIDERATIONS

TABLE OF CONTENTS

MODEL RSE 2 

10/14 SERIES

115, 208, 230 Vac.

Patents 5,334,347; 5,817,276; 5,866,076; 6,245,293; 6,267,924;

6,280,686; 6,313,470; 6,372,186; 6,423,882; 6,500,267; 6,589,476; 6,627.000.

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

Improper installation, adjustment, alteration, service,
maintenance, or use can cause fire, electrical shock, or
other conditions which may cause personal injury or prop-
erty damage. Consult a qualified installer, service agency,
or your supplier for information or assistance.

The qualified installer or agency must use factory kits or
accessories when installing this product.

Refer to the

individual instructions packaged with kits or accessories
when installing them.

Follow all safety codes, wear safety glasses and work
gloves. Read all instructions thoroughly and follow any
warnings or cautions attached to any accessed area.
Consult local building codes and the National Electrical
Code (NEC) for special requirements.

Understand the signal words 

DANGER, WARNING

or

CAUTION.

These words are universally used for overall

safety.

DANGER

identifies the most serious hazards,

which will result in severe personal injury or death.

WARNING

signifies hazards, which could result in

personal injury or death.

CAUTION

is used to identify

unsafe practices, which would result in minor personal
injury or product and property damage.

SECONDS, REINSTALL

120-230 V

Содержание RSE 2-10 Series

Страница 1: ...rrect Lamp can result in damage to accessory or lamp Safety Considerations 1 0 General 2 0 Installation 3 0 Operation Maintenance 4 0 Trouble Shooting 5 0 Illustrations 6 0 Spare or Replacement Parts 7 0 1 0 SAFETY CONSIDERATIONS TABLE OF CONTENTS MODEL RSE 2 10 14 SERIES 115 208 230 Vac Patents 5 334 347 5 817 276 5 866 076 6 245 293 6 267 924 6 280 686 6 313 470 6 372 186 6 423 882 6 500 267 6 5...

Страница 2: ...a template scribe and then create two insertion holes 1 diameter on the mounting surface for the Emitters Drill suitable holes for each fastener unless using self taping screws Using the proper 10 fastener for your application install fixture s and wire in accordance with the applicable code 3 6 Insert Emitter lamp into the fixture without touching glass with bare hands if necessary clean using a ...

Страница 3: ...eplace Emitter with new unit Normal replacements recommended once per year 5 Check line voltage 6 Check wiring to Emitter 7 Replace power supply 5 2 Low Output Radiometer Reading or Visibly Weak Light 1 Replace Emitter with new unit 2 Check line voltage 3 Check wiring to Emitter 5 3 Red Orange Light 1 Check ambient temperature If the temperature is at or below 35 F Emitter is too cold to operate p...

Страница 4: ...of this product and its ability to aid in disinfection of environment air has not been investigated by UL 4 1320 7 0 SPARE OR REPLACEMENT PARTS ITEM 7 1 7 2 7 3 7 4 7 5 7 6 7 7 7 8 7 9 7 10 7 11 7 14 7 15 7 16 DESCRIPTION POWER SUPPLY 115 208 230V BASE COVER SPRING SWITCH ROCKER SWITCH INTERLOCK WARNING LABEL CLEANING KIT MOUNTING KIT 6 CORD KIT 115 V 6 CORD KIT 208 230 V EMITTERS RGTS 20 HO RGTS ...

Отзывы: