manualshive.com logo in svg

Stellar Hearth Products 34S-20GL, Инструкция по установке и эксплуатации

Поделиться
Скачать
Stellar Hearth Products 34S-20GL Скачать руководство пользователя страница 47

Page 47

16400-7806 G4S REV G

B - NON-COMBUSTIBLE BACKER       

     CEMENT BOARD

E - COMBUSTIBLE 

MANTEL

F - COMBUSTIBLE 

HEARTH

G. ACCESS PANEL

I. COMBUSTIBLE FRAMING 

AND FINISHING MATERIAL

C - COMBUSTIBLE FINISHING MATERIAL

A B

STANDOFF

REFER TO (B)

D - COMBUSTIBLE OR NON-COMBUSTIBLE  

 

      BACKER MATERIAL (I.E. SHEETROCK)

A. No combustible materials may be within 6” [152mm] of the top of the fireplace.
B. 1/2” [12.7]  CLEARANCE TO COMBUSTIBLES ON SURFACE. The fireplace ships with standoffs in place to ensure a 1/2” clearance to     
combustibles is maintained on the surface. See Figure 10A.1. If the standoffs are removed, only non-combustible material can be installed against  
the surface of the fireplace such as a non-combustible backer cement board. 1/2” [12.7mm] minimum thickness must be used in the space* between 
the top of the 3’’ trim to the combustible framing the full width of the fireplace. The space* includes a 7” [178mm] minimum above the top of the 
fireplace that is recommended for ease of attachment. *= 15" [381] for 3'-7' units and 19" [483] for 8' units.See Figure 10A.2
C. Combustible material may cover the non-combustible area mentioned in B. 
D. Combustible finishing materials allowed.
E. Combustible mantel may be placed above the top of the glass viewing area. There are no restrictions on mantel depth.
F. Combustible hearth may be placed below the bottom of the glass viewing area. 
G. Flat covers will cover the components access.  Gas and electric inlets are located behind this panel. There are four access panel options all  
     located on the pilot side of the fireplace; front (shown above), side, back and inside behind the glass. 
     Please take consideration of which option will be used to access the components for service later during planning. 
I. Combustible framing and finishing materials allowed.

3” TOP TRIM

COMBUSTIBLE FRAMING

11 - FINISHING

A.2 FINISHING THE WALL - 

NOT

 USING THE PROVIDED 1/2" STANDOFFS

NOTE: REFER TO DIMENSIONS SECTION FOR ALLOWABLE FINISHING DIMENSIONS REQUIRED TO FIT THE GLASS 

 

PANELS INTO THE FIREPLACE. FINISHING MATERIALS MUST NOT OVERLAP THE DIMENSIONS HIGHLIGHTED IN GREEN ON 

PAGE 5. NEVER COVER THE GLASS WITH FINISHING MATERIALS.

NOTE: REFER TO 

SECTION 5 MANTEL REQUIREMENTS: NON-COMBUSTIBLE ZONE USING PROVIDED 1/2" STANDOFFS FOR 

MORE INFORMATION.

Figure 11A.2

NOTE: 

DO NOT 

FOUR SIDEDCE ANY OF THE BLACK PAINTED SURFACES WITH SCREWS, RIVETS, ETC. 

 

THIS INCLUDES THE 3" BLACK TOP AND BOTTOM GLASS TRIM AND ANY PAINTED SIDES ADJACENT TO THE GLASS. 

Содержание 34S-20GL
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды