- 24 -
- 25 -
The constant light level can be activated
for individual groups. For groups 2 and 3,
a brightness offset can be set between
-100% to +100%. This offset is calculat-
ed based on group 1.
Constant-lighting control setting
This parameter can be used for defining
the target value for constant-lighting
control. If, for example, 500
lx is set, the
presence detector attempts to maintain
this value through dimming/increasing
the light. In teach mode, this value is
determined automatically and over-
written. If constant-lighting control is
enabled, this value will be adopted as
the dimming threshold so long as a
brightness-based basic light level has
not been set.
Constant-lighting control starting level
This parameter can be used for defining
the switch-on value for the lighting when
constant-lighting control is enabled. The
lighting switches on with the set value
and will then be regulated to the target
value.
Constant-lighting control fixed /
Constant-lighting control dynamic
In fixed mode, the sensor does not save
a manual override of the constant-lighting
control made via a button. In contrast, in
dynamic mode, the new brightness level
will be set as the control threshold.
If there is a manual override without
constant-lighting control enabled in the
dynamic mode, the current light level will
be set as the new value for "Main light
dimming".
6.14 Initial state
The setting of the initial state can be used
to determine whether the connected
DALI lights should switch on immediately
to the set main light level after switching
on the supply voltage (On) or only come
on when there is movement (Off). This
setting is saved in the DALI ECGs and
is therefore only valid for the local DALI
network. The setting is not adopted by
the other Bluetooth group devices.
6.15 Auto ON semi-automatic mode
In semi-automatic mode, the light is only
switched off automatically. If the semi-au-
tomatic auto-ON function is enabled, light
is also switched on again if the luminaire is
still in basic lighting mode and move-
ment is being detected or if movement is
detected within 30 seconds of complete
deactivation (no movement and stay-ON
time elapsed).
6.16 Buttons
The function of the buttons is specified
in broadcast mode (factory setting).
Each button can switch and dim in both
directions.
For the addressed mode, the group
association and the function of the
connected buttons can be defined in
the "DALI addressing" menu. To do this,
the devices must first be addressed and
the lights assigned to a group. This also
applies to a button connected to the S
input, a button connected to the S input
of a Bluetooth device or one of the up to
four addressable DALI buttons.
7. Maintenance and care
The product requires no maintenance.
The sensor can be cleaned with a damp
cloth (without detergents) if dirty.
8. Disposal
Electrical and electronic equipment,
accessories and packaging must be
recycled in an environmentally com-
patible manner.
Do not dispose of electrical
and electronic equipment as
domestic waste.
EU countries only
Under the current European Directive on
Waste Electrical and Electronic Equip-
ment and its implementation in national
law, electrical and electronic equipment
no longer suitable for use must be
collected separately and recycled in an
environmentally compatible manner.
9. Conformity
STEINEL Vertrieb GmbH hereby declares
that the True Presence/Hallway radio
equipment type conforms to Directive
2014/53/EU. The full wording of the EU
Declaration of Conformity is available for
downloading from the following Internet
address: www.steinel.de.
10. Manufacturer's Warranty
As purchaser, you are entitled to your
statutory rights against the vendor. If
these rights exist in your country, they
are neither curtailed nor restricted by
our Warranty Declaration. We guarantee
that your STEINEL Professional sensor
product will remain in perfect condition
and proper working order for a period of
5 years. We guarantee that this product
is free from material-, manufacturing- and
design flaws. In addition, we guarantee
that all electronic components and
cables function in the proper manner and
that all materials used and their surfaces
are without defects.
Making Claims
If you wish to make a claim, please send
your product complete and carriage paid
with the original receipt of purchase,
which must show the date of purchase
and product designation, either to your
retailer or contact us at
STEINEL (UK)
Limited, 25 Manasty Road, Axis Park,
Orton Southgate, Peterborough, PE2
6UP,
for a returns number. For this rea-
son, we recommend that you keep your
receipt of purchase in a safe place until
the warranty period expires. STEINEL
shall assume no liability for the costs or
risks involved in returning a product.
For information on making claims under
the terms of the warranty, please go to
www.steinel-professional.de/garantie
If you have a warranty claim or would
like to ask any question regarding your
product, you are welcome to call us at
any time on our Service Hotline
01733 366700
.
MANUFACTURER'S
1
3
5
Y E A R
G B
WARRANTY
MANUFACTURER'S
Y E A R
WARRANTY
MANUFACTURER'S
Y E A R
WARRANTY
GB
