SteelMax SM-BM-16 Скачать руководство пользователя

Страница: 6 / 32

SM-BM-16

SM-BM-

16 Operator’s Manual

2. SAFETY PRECAUTIONS

Before use, read this Operator’s Manual and complete a training in occupational

safety and health.

Use only in applications specified in this Operator’s Manual.

3. Make sure that the

machine has all parts and they are genuine and not damaged.

4. Make sure that the specifications of the power source are the same as those

specified on the rating plate.

5. Do not carry the machine by the cord and do not pull the cord. This can cause

damage and electric shock.

6. Keep untrained bystanders away from the machine.

7. Before each use, ensure the correct condition of the machine, power source,

power cord, plug, control parts, and milling tools.

8. Before each use, make sure that no part cracked or loose. Make sure to maintain

correct conditions that can have an effect on the operation of the machine.

9. Keep the machine dry. Do not expose the machine to rain, snow, or frost.

10. Keep the work area well-lit, clean, and free of obstacles.

11. Do not use near flammable materials, or in explosive environments.

12. Use only tools specified

in this Operator’s Manual.

13. Do not use tools that are dull or damaged.

14. Make sure that the cutting inserts and the milling head are correctly attached.

Remove wrenches

from

the

work

area

before you connect

the

machine

the

power source.

15. Do not use the machine so that the milling head points up.

16. If the cutting edge of an insert is worn, rotate the insert by 90° or 180°. If all

possible to use edges are worn, install new inserts specified in this Operator’s

Manual.

17. Use eye and ear protection, non-skid footwear, and protective clothing. Do not

use loose clothing.

18. Do not touch chips or moving parts. Do not let anything catch in moving parts.

19. After each use, clean the machine and the milling head with a cotton cloth and no

chemical agents. Do not remove chips with bare hands.

20. Maintain the machine and install/remove parts and tools

only after you unplug the

machine from the power source.

Содержание SM-BM-16

































Результаты поиска

Содержание SM-BM-16

Отзывы:

Похожие инструкции для SM-BM-16

Бренды по названию

Популярные бренды

SteelMax SM-BM-16, Руководство оператора

Результаты поиска

Содержание SM-BM-16

Отзывы:

Похожие инструкции для SM-BM-16

Бренды по названию

Популярные бренды