SteelMax D3X L Скачать руководство пользователя страница 7

Страница: 7 / 34

D3X R/L / D3XS R/L

D3X R/L / D3XS R/L

Operator’s Manual

2. SAFETY PRECAUTIONS

1. Before beginning, read this Ope

rator’s Manual and complete proper occupational

safety and health training.

2. The

machine

must be used only in applications specified in this Operator’s Manual.

3. The

machine

must

complete

and

all parts must be genuine and fully operational.

4. The

electrical

supply

specifications

must

conform

those

specified

the

rating

plate.

5. The machine must be plugged into a properly grounded (earthed) socket-outlet. The

electrical supply must be protected with a 16 A fuse for 230 V or a 32 A fuse for

115 V. When used on building sites, supply the machine through an isolation

transformer made in II protection class.

6. Never carry the machine by the cord or pull it to disconnect the plug from the

power outlet as this may damage the power cord and result in electric shock.

7. Transport

and position the machine using the carrying handle, with the magnet

switch set to position

‘O’.

8. Untrained bystanders must not be present in the vicinity of the machine.

9. Before

beginning,

check the condition of the machine and electrical supply, including

the power cord, plug, control panel components, and milling tools.

10. Keep the machine dry. Exposure to rain, snow, or frost is prohibited.

11. Never stay below the machine placed at heights.

12. Keep the work area well lit, clean, and free of obstacles.

13. Mount the annular cutter securely using the set screws. Remove adjusting keys

and wrenches from the work area before connecting the plug to the power outlet.

14. Never use dull or damaged tools.

15. Mount and dismount tools using protective gloves and with the power cord

unplugged from the power outlet.

16. Never use annular cutters without the pilot pin except for establishing incomplete

through holes. Never use arbors without the spring.

17. Never use the machine in the vicinity of flammable liquids or gases, or in explosive

environments.

18. Using the machine on surfaces that are rusty, covered with a thick paint layer,

uneven, or not stiff is prohibited.

19. Do not start operation in the case of excessive slider clearance.

Содержание D3X L



































Результаты поиска

Содержание D3X L

Отзывы:

Похожие инструкции для D3X L

Бренды по названию

Популярные бренды

SteelMax D3X L, Руководство оператора

Результаты поиска

Содержание D3X L

Отзывы:

Похожие инструкции для D3X L

Бренды по названию

Популярные бренды