background image

Rotary Tool

24

Recommended Speeds

The following tables display recommended speed ranges for various 
accessories on various materials.

High-speed cutters

Soft wood: 10

Hard wood: 6 - 10

Laminates & plastic: 4 - 6

Steel: 6

Aluminum, brass, etc.: 6-10

Engraving cutters

Soft wood: 10

Hard wood: 10

Laminates & plastic: 6 - 8

Steel: 4

Aluminum, plastics, etc.: 6

WARNING!  NEVER RUN ACCESSORIES AT SPEEDS EXCEEDING THE 
LISTED MAXIMUMS. ACCESSORIES COULD BREAK APART AND 
SCATTER FLYING DEBRIS AT HIGH-SPEED, POSSIBLY CAUSING 
SERIOUS INJURY.

CAUTION: IT IS HIGHLY RECOMMENDED THAT YOU NOT 
EXCEED THE RECOMMENDED SPEEDS FOR THE LISTED 
ACCESSORY/MATERIAL COMBINATION AS DOING SO 
COULD HARM THE WORK PIECE. ALWAYS EXPERIMENT 
WITH A PIECE OF SCRAP MATERIAL TO ENSURE OPTIMUM 
SETTINGS BEFORE BEGINNING ANY WORK ON AN ACTUAL 
PRODUCT.

Note: Where a speed range (such as 4 - 8) appears, experiment 
at the lower end of the range first and gradually increase the 
speed to obtain best results. Never exceed the recommended 
speed range to avoid damaging the work piece and never 
exceed the accessory’s maximum speed.

Содержание SP-PT253
































Отзывы: