manualshive.com logo in svg

Steelcase V.I.A. FEIJA2V, Руководство пользователя

Поделиться
Скачать
Steelcase V.I.A. FEIJA2V Скачать руководство пользователя страница 20

Page 20 of 38

939502326 Rev G

'L' Configuration

'T' Configuration

In-line Configuration

Process for Carpet and Tile Floor tape 

application ONLY
•

  Floor glide to be cleaned using Acetone soaked cloth prior

to applying pressure sensitive tape or carpet gripper tape.

•

  Attach pressure sensitive tape for 24 hours prior to loading. 

(Confirm application with local building codes)
or

•

  Attach carpet gripper tape for 24 hours prior to loading. 

(Confirm application with local building codes)

CAUTION:  When installing Steelcase V.I.A. over Steelcase Low-Profile floor, floor

guide (style number FEFG) MUST be applied to all leveler screws to distribute

wall / applied furniture loading. Failure to consider application and loading

may result in wall disengagement from ceiling track, resulting in personal injury. 

NOTE:  When the V.I.A. Wall is fully loaded, the wall has the potential to deliver 1,200 pounds per leveler screw to floor

condition. Leveler screws loaded to 1,200 pounds will exert local pressure loading of 11,000 PSI. Floor type / Steelcase

product application must be properly matched in accordance with local building codes and floor condition to avoid flooring

damage and ensure proper performance of Steelcase Wall Systems. 

Chalk Line

Floor Guide

Base

Track

Base

Track

Chalk Line

Chalk Line

Floor Guides

Chalk Lines

Floor Guides

Base

Track

Floor Guide

Pressure Sensitive Tape

or Carpet Gripper Tape

Mechanical fastening ONLY
•

  Consult local building codes.

NOTE:  Fasteners shown for

mechanical fastening only.

NOTE:  Fasteners shown for

mechanical fastening only.

NOTE:  Fasteners shown for

mechanical fastening only.

4" Min.

2" Max.

1" Min.

6" Min.

1" Min.

6" Min.

Carpet Application:

Hard Floor
Application:

Structural Fastener

NOTE:  Mounting hardware must be specified/verified by the designated design professional by the AHJ. 

Floor Guide

NOTE:  Floor guides may be needed at vertical posts and junctions when adjacent to a door frame.

Содержание V.I.A. FEIJA2V







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды