Steelcase FitWork 7 Series Скачать руководство пользователя страница 20

Страница: 20 / 20

Page 20 of 20

005720D Rev F

When connecting cables as stated in step 15 on page 7,

use this guide as a reference.

Connect the cables from the Lift Columns to the cables

provided. The other end should be connected to the Control

Box. Repeat this for each leg.

Connect the end of the Controller cable into the Control Box.

Follow Steps 15 through 17 beginning on page 8

to complete

the wiring installation.

Once you have completed the wiring, use the Wire

Management Cableways to hold all the cables and minimize

possible entanglements.

NOTE:

Cableways and vertical wire management

solutions are also available. Contact us for more

information.

Wiring Guide

ATTACHMENT
PLATE

FOOT

GLIDES

CONTROL BOX

• Never

attach wires to the

legs or stretcher in any way.

CONTROL

RIGHT LIFT

COLUMN

LEFT LIFT

COLUMN

STRETCHER

Содержание FitWork 7 Series





















Результаты поиска

Содержание FitWork 7 Series

Отзывы:

Похожие инструкции для FitWork 7 Series

Бренды по названию

Популярные бренды

Steelcase FitWork 7 Series, Руководство пользователя

Результаты поиска

Содержание FitWork 7 Series

Отзывы:

Похожие инструкции для FitWork 7 Series

Бренды по названию

Популярные бренды