Steelcase FitWork 7 Series Скачать руководство пользователя страница 2

Страница: 2 / 20

Page 2 of 20

005720D Rev F

1
2

STRETCHER

ELECTRICAL
PIGTAIL

Unpack and sort all components.
Position top upside down on the assembly surface.

Layout the left and right lift columns, lift the stretcher

into each dovetail, connect loosely. (Left and right is

determined when the table is standing on the base

and is viewed from the front.)

Note:

A clean, abrasion free

surface will be necessary for

table assembly.

Worksurface Assembly

NOTCH

RIGHT COLUMN

LEFT COLUMN

STRETCHER

DOVETAIL

COLUMN

STRETCHER

TOP VIEW

For each lift column, fold the electrical 'pig-tail' towards

the center of the surface. Secure in the notch

provided in each lift column.

REAR VIEW

Once each lift column has been engaged, lightly tap each

connection point with a rubber mallet 1/8-1/4 inch at a time, until

completely seated. Do not completely install one lift column at a

time...they must be installed incrementally.

FLUSH

Содержание FitWork 7 Series





















Результаты поиска

Содержание FitWork 7 Series

Отзывы:

Похожие инструкции для FitWork 7 Series

Бренды по названию

Популярные бренды

Steelcase FitWork 7 Series, Руководство пользователя

Результаты поиска

Содержание FitWork 7 Series

Отзывы:

Похожие инструкции для FitWork 7 Series

Бренды по названию

Популярные бренды