Steelcase c:scape Скачать руководство пользователя страница 21

Страница: 21 / 24

3" LESS THAN

OVERALL LENGTH

3" LESS THAN

OVERALL LENGTH

DESIRED

CENTERLINE

3/4"

12"

Page 21 of 24

939500367 Rev E

Benching - Mounted Parallel to
Beam Tethered to Storage

Attach legs to understructure

•"L" leg uses 24" or 30" depending on

worksurface depth.

Attach tethers to beam

•Sub-assemble tether "position B" and

shared plate center position.

•Lower shared tether 1 detent (1/2") to

account for plate

•Attach 2nd and 3rd tethers depending on

application:

-Benching application, one end shared:

3" less than overall width of desk.

-Benching application, both end shared:

same as overall width of desk.

Slide storage unit up to beam

•The back edge of the storage unit should be

flush with desired centerline.

Attach tethers

•1st tether to be 8-1/2" from beam furthest

edge.

•2nd tether to be 12" from 1st tether.

8-1/2"

Содержание c:scape

























Результаты поиска

Содержание c:scape

Отзывы:

Похожие инструкции для c:scape

Бренды по названию

Популярные бренды

Steelcase c:scape, Руководство пользователя

Результаты поиска

Содержание c:scape

Отзывы:

Похожие инструкции для c:scape

Бренды по названию

Популярные бренды