Steelcase c:scape Low Storage Series Скачать руководство пользователя страница 7

Страница: 7 / 15

Glide Adjustment

Page 7 of 15

939500368 Rev K

Installation of the Glides
and Leveling the Case

CAUTION:

Counterweights

may be required. See

assembly direction

939500370.

With the help of an assistant, tip the

case onto a shipping blanket on its back.

Install storage glide by lining up

holes with glide and assemble with
screws provided. Repeat for the
remaining glides.

With the help of an assistant,

tip the case upright on its glides.
To adjust the height of glide, turn
lower portion of glide clockwise to
lower and counter-clockwise to raise
the case until case is level.

NOTE:

The glide is set for an overall

case height of 24" for a 1-1/2 High low
storage and a case height of 18" for a
1 High low storage.

NOTE:

30”, 36”, 42” and 48” wide

cases require four (4) glides. 60” and
72” wide cases require a 5th glide
located at the front center of the unit.

Glide Installation

GLIDE

NOTE GLIDE MOUNTING HOLE
CONFIGURATION TO BASE

Содержание c:scape Low Storage Series
















Результаты поиска

Содержание c:scape Low Storage Series

Отзывы:

Бренды по названию

Популярные бренды

Steelcase c:scape Low Storage Series, Руководство по сборке

Результаты поиска

Содержание c:scape Low Storage Series

Отзывы:

Бренды по названию

Популярные бренды